Laptop Mode Tools

For this you need to have hdparm and/or sdparm installed. See Hdparm.

Spinning down the hard drive through values saves power and makes everything a lot more quiet. LMT can also establish values. The maximum hard drive power saving is 1 and the minimum is 254. For example, set this value to 254 when on AC and 20 when on battery. If you find that normal activity hangs often while waiting for the disk to spin up, it might be a good idea to set it to a higher value (e.g. 128) which will make it spin down less often. and values are configured in /etc/laptop-mode/laptop-mode.conf.

With the CONTROL_MOUNT_OPTIONS variable (default on), laptop-mode-tools automatically remounts your partitions, appending in the mount options. This keeps the journaling program jbd2 from accessing your disk every few seconds, instead the disk journal gets updated every 10 minutes.

From the official, upstream FAQ:

Question: I have a solid-state disk (SSD) in my machine. Should I enable any of the disk-related parts of laptop-mode-tools, or are they irrelevant?

Answer: They may be relevant, because (a) laptop mode will reduce the number of writes, which improves the lifetime of an SSD, and (b) laptop mode makes writes bursty, which enables power saving mechanisms like ALPM to kick in. However, your mileage may vary depending on the specific hardware involved. For some hardware, you will get no gain at all, for some the gain may be substantial.

For this you need to have a CPU frequency driver installed. See CPU frequency scaling.

# cpufreq.conf
# ThinkPad T40/T42/T60 Example
#
CONTROL_CPU_FREQUENCY=1
BATT_CPU_MAXFREQ=fastest
BATT_CPU_MINFREQ=slowest
BATT_CPU_GOVERNOR=ondemand
BATT_CPU_IGNORE_NICE_LOAD=1
LM_AC_CPU_MAXFREQ=fastest
LM_AC_CPU_MINFREQ=slowest
LM_AC_CPU_GOVERNOR=ondemand
LM_AC_CPU_IGNORE_NICE_LOAD=1
NOLM_AC_CPU_MAXFREQ=fastest
NOLM_AC_CPU_MINFREQ=slowest
NOLM_AC_CPU_GOVERNOR=ondemand
NOLM_AC_CPU_IGNORE_NICE_LOAD=0
CONTROL_CPU_THROTTLING=0

Enable the Intel SATA AHCI controller Aggressive Link Power Management feature to set the disk link into a very low power mode in the absence of disk IO.

# intel-sata-powermgmt.conf
# ThinkPad T40/T42/T60 Example
#
DEBUG=0
CONTROL_INTEL_SATA_POWER=1
BATT_ACTIVATE_SATA_POWER=1
LM_AC_ACTIVATE_SATA_POWER=1
NOLM_AC_ACTIVATE_SATA_POWER=0

# runtime-pm.conf
# ThinkPad T40/T42/T60 Example
#
DEBUG=0
CONTROL_RUNTIME_AUTOSUSPEND=1
BATT_SUSPEND_RUNTIME=1
LM_AC_SUSPEND_RUNTIME=1
NOLM_AC_SUSPEND_RUNTIME=1
AUTOSUSPEND_TIMEOUT=2

Available brightness values for certain laptops can be obtained by running following command:

$ cat /proc/acpi/video/VID/LCD/brightness

For ThinkPad T40/T42 notebooks, minimum and maximum brightness values can be obtained by running:

$ cat /sys/class/backlight/acpi_video0/brightness
$ cat /sys/class/backlight/acpi_video0/max_brightness

# lcd-brightness.conf
# ThinkPad T40/T42 Example
#
DEBUG=0
CONTROL_BRIGHTNESS=1
BATT_BRIGHTNESS_COMMAND="echo 0"
LM_AC_BRIGHTNESS_COMMAND="echo 7"
NOLM_AC_BRIGHTNESS_COMMAND="echo 7"
BRIGHTNESS_OUTPUT="/sys/class/backlight/thinkpad_screen/brightness"

For ThinkPad T60 notebooks, minimum and maximum brightness values can be obtained by running:

$ cat /sys/class/backlight/thinkpad_screen/max_brightness
$ cat /sys/class/backlight/thinkpad_screen/brightness

# lcd-brightness.conf
# ThinkPad T60 Example
#
DEBUG=0
CONTROL_BRIGHTNESS=1
BATT_BRIGHTNESS_COMMAND="echo 0"
LM_AC_BRIGHTNESS_COMMAND="echo 7"
NOLM_AC_BRIGHTNESS_COMMAND="echo 7"
BRIGHTNESS_OUTPUT="/sys/class/backlight/acpi_video0/brightness"

# terminal-blanking.conf
# ThinkPad T40/T42/T60 Example
#
DEBUG=0
CONTROL_TERMINAL=1
TERMINALS="/dev/tty1"
BATT_TERMINAL_BLANK_MINUTES=1
BATT_TERMINAL_POWERDOWN_MINUTES=2
LM_AC_TERMINAL_BLANK_MINUTES=10
LM_AC_TERMINAL_POWERDOWN_MINUTES=10
NOLM_AC_TERMINAL_BLANK_MINUTES=10
NOLM_AC_TERMINAL_POWERDOWN_MINUTES=10

# ethernet.conf
# ThinkPad T40/T42/T60 Example
#
DEBUG=0
CONTROL_ETHERNET=1
LM_AC_THROTTLE_ETHERNET=0
NOLM_AC_THROTTLE_ETHERNET=0
DISABLE_WAKEUP_ON_LAN=1
DISABLE_ETHERNET_ON_BATTERY=1
ETHERNET_DEVICES="eth0"

Wireless interface power management settings are hardware-dependent, and thus a bit trickier to configure. Depending on the wireless chipset, the settings are managed in one of the following three files:

1. for a generic method of saving power (using "iwconfig wlan0 power on/off"). This applies to most chipsets (that is, anything but Intel chipsets listed below).
2. for Intel chipsets driven by the old ipw driver. This apply to IPW3945, IPW2200 and IPW2100. It currently (as of LMT 1.55-1) uses iwpriv for IPW3945, and a combination of iwconfig and iwpriv settings for IPW2100 and IPW220. See /usr/share/laptop-mode-tools/modules/wireless-ipw-power for details. (note that the ipw3945 is not used anymore, see below)
3. for Intel chipsets driven by modules iwl4965, iwl3945 and iwlagn (this latter supports chipsets 4965, 5100, 5300, 5350, 5150, 1000, and 6000)

Note that activating the three of them should not be much of a problem, since LMT detects the module used by the interface and acts accordingly.

The supported modules for each configuration file, indicated above, are taken directly from LMT. However, this seems to be a bit out-of-date, since the current 2.6.34 kernel does not provide the ipw3945 and iwl4965 modules anymore (3945 chipset uses iwl3945 instead, and 4965 uses the generic module iwlagn). This is only brought here for information, as this does not (or should not) affect the way LMT works.

There is a known issue with some chipsets running with the iwlagn module (namely, the 5300 chipset, and maybe others). On those chipsets, the following settings of :

IWL_AC_POWER
IWL_BATT_POWER

are ignored, because the file does not exist. Instead, the standard method (with ) is automatically used.

# ac97-powersave.conf
# ThinkPad T40/T42/T60 Example
#
DEBUG=0
CONTROL_AC97_POWER=1

# intel-hda-powersave.conf
# ThinkPad T40/T42/T60 Example
#
DEBUG=0
CONTROL_INTEL_HDA_POWER=1
BATT_INTEL_HDA_POWERSAVE=1
LM_AC_INTEL_HDA_POWERSAVE=1
NOLM_AC_INTEL_HDA_POWERSAVE=0
INTEL_HDA_DEVICE_TIMEOUT=10
INTEL_HDA_DEVICE_CONTROLLER=0

Install and enable .

If that does not help, go through the laptop-mode configuration files and make sure that the service you want to enable is set to 1. Many services (including cpufreq control) are by default set to "auto", which may not enable them.

Issues with bluetooth not working when booting up with battery are fixed with disabling runtime-pm.

First find the ID of you device (it should look like 046d:c534):

$ lsusb

Put this value into the variable in , for example:

Multiple IDs can be seperated with spaces.

When laptop mode is enabled, KDE fails to start. The reason is that the default KDE display manager (SDDM) starts before the NVIDIA driver. To prevent this from happening you need to remove the nomodeset kernel parameter.

As described before, laptop-mode-tools affects the NVIDIA driver. Adding the kernel parameter reduces boot time dramatically.