AJS/Matchless Lightweight Gearbox Removal

Written By: Paul Barnfather
  • Comments: 2
AJS/Matchless Lightweight Gearbox Removal

Difficulty

Moderate

Steps

8

Time Required

1 hour

Introduction

This guide will show you how to remove the gearbox from a 250cc AJS Model 14 / Matchless G2 or a 350cc AJS Model 8 / Matchless G5 motorcycle (all years).

You will need a set of Whitworth spanners or sockets and a decent flat-bladed screwdriver.

Note that the bike featured in this guide has a few modifications from standard, so your bike may look a little different in places. The basic technique remains the same, regardless of which model of Lightweight you have.

  1. SfjLhMCPDGwCulXX
    SfjLhMCPDGwCulXX
    YbOywWnkbechLnJG

    • Remove the six screws holding the primary drive cover on.

    • You can either drain the oil first, or just put a dish underneath to catch the oil spillage.

    • Lift the cover away. Note that the cables to the alternator will still be attached, so make sure the cover is supported and not pulling on the cables.

  2. lGscwktgKRVHYrhw
    lGscwktgKRVHYrhw
    bYIktseDuncXt1DC
    DrfHpIlWpZ1XeHmJ

    • Unscrew the clutch springs with a piece of flat metal.

    • Lift off the clutch cover and withdraw the clutch operating rod and clutch plates.

    • Engage a gear and undo the clutch retaining nut. This is likely to be tight; it will undo more easily if you "shock" it loose with light hammer taps onto a socket driver.

    • If you are lucky, the clutch will be loose on the shaft. If it is stuck fast, you may need to use the special puller.

  3. BtKuui2qyHGaqxCa
    BtKuui2qyHGaqxCa
    UsmY2sq6IbqNgVDG
    XelChKEXEnUhVYhH

    • Remove the kickstart.

    • Remove the gear position indicator (if fitted) and the gear lever.

    • Remove the exhaust.

    • You may need to remove other ancillaries such as footrests and chain cover (not shown in these pictures)

    • Remove the link from the rear chain and move it clear of the gearbox sprocket.

    • Drain the oil from the gearbox.

  4. ykv23ccSsLJusMGk
    ykv23ccSsLJusMGk
    3HAOXiFbUAhWuTBe

    • Undo the four screws holding the right side cover on and remove it.

    • Some trapped oil may run out if there are any leaks on this side of the engine.

    • Undo the two screws holding the inspection cover on and remove it.

  5. BrnLRDIyIOLNTTuS
    BrnLRDIyIOLNTTuS
    lOta3vq24md2dLQX

    • Slacken off the clutch cable completely at the handlebar end and release it from the clutch lever.

    • Push the cable through to release it at the gearbox end.

    • Look in through the gearbox inspection hole and release the cable from the operating fork.

    • Withdraw the clutch cable from the gearbox and put it to one side.

  6. 5HL2TOvPbrhl2JA1
    5HL2TOvPbrhl2JA1
    Cfn6vCV5XcEFc4J6
    AWaY1JVWSkuUH13M

    • Remove the two barrel bolts from the gearbox retaining bands.

    • Remove the two nuts holding the tensioner in place.

    • Withdraw the tensioner and the two spacers either side of the gearbox mounting tab.

  7. iZXHoA5VebYmBHJO
    iZXHoA5VebYmBHJO
    bUcWVgJjsXVBRRMR

    • Remove the two nuts at the rear of the mounting plate.

    • Lift the mounting plate away.

    Can I get gear box of AJS Bike of 350cc 1970 make.

    My name is Mahadev bhosle

    royal.bhosale@gmail.com

    Mahadev Bhosale -

  8. 5tnwJohOAk2U5keq

    • You can now lift the gearbox away from the bike.

    • Don't forget to hold on to the clutch basket on the other side of the bike. It will fall away as you remove the gearbox.

Conclusion

See my other guide on how to overhaul the gearbox...

Author

Paul Barnfather

Member since: 30/05/17

974 Reputation

One comment

Paul, Any chance of contacting me on dave.jch@btinternet.com

David Charlton -