Introduction

Hey there!

On this guide, I will show you how to remove a broken towel hook on drywall, patch the hole, and install a new one!

Before you start, make sure you have the required tools and be careful around the screwdriver!

This guide will not take long, only around 10-15 minutes, but you’ll have to come back to this a few hours after you’re done installing the new hook to clean up the old hole.

Happy Fixing!

  1. rP4Nywtc3rwOxwF6
    rP4Nywtc3rwOxwF6
    CdqBtRTD1j3evhIq
    • Using your Phillips screwdriver, remove both screws that are keeping your current (broken) drywall hook in place.

    • Make sure you remove both screws evenly, to avoid bending and damaging the screws and the drywall around it.

  2. 2oqATXYYYC1YS4Rs
    • After removing both screws, remove the plastic anchor screws from the drywall.

    • It will leave a big hole, but we will fix that!

  3. ItORsjfO5eQOwgLt
    ItORsjfO5eQOwgLt
    gCFWorunWsPbrqku
    2jDg4CDpk4Tkpiy6
    • After removing the anchor screws, take your spatula and press it flush with the wall. Remove debris from the drywall to make the wall flat.

  4. sYvm3YBfkPxjuWVP
    sYvm3YBfkPxjuWVP
    UZZAsPmYqHtnALXZ
    • Take some patching and with your spatula, apply it on and around the holes in order to fill it up to the surface of the wall.

  5. AOqlPlCTNpZXJTtG
    AOqlPlCTNpZXJTtG
    A1K5U5MIm4csjKHT
    • Select a new location for your new towel hook and, with one of the screws, mark the spot where you'll drill the holes.

    • Use your screwdriver to tap the two new locations, to make it easier to screw the anchors onto the wall.

  6. xwAne1xm4H1iHPeX
    xwAne1xm4H1iHPeX
    VIQMtNnhXrJwf1Hg
    • Take your new anchor screws and start drilling on your marked holes.

    • Keep screwing them into the drywall until they're flush with the wall.

    • Don't drill too far, or else it will damage the drywall and the towel hook will be uneven!

  7. FYBdNCsyQRFTUvWG
    FYBdNCsyQRFTUvWG
    ulFxRZCghgeECd5F
    MkWIodf3mZxciabc
    • Line up your new towel hook with the holes where the anchors are located.

    • Take your screws and start screwing them in manually so they stay in place.

  8. oFLypGgSN4LEri5s
    • With your screwdriver, continue screwing the screws in until they're flush with the towel hook.

  9. MwhpQ1TRGiEpml1U
    • Voila! Your new towel hook is installed!

    • But how about the hole we patched earlier?

  10. A2uVY3LE3V3GqWtW
    A2uVY3LE3V3GqWtW
    kCrrPekCT1EW2vPx
    • Press the sandpaper against the wall and scrub on and around the hole, to level it with the wall.

    • After doing that for a few seconds, your patch should be leveled and your problem, solved!

Conclusion

This guide shows both removing the old, broken towel hook and installing the new towel hook! Hope it helped!

Pietro Coso

Member since: 21/03/20

211 Reputation

0 comments