Motorola Moto E4 Plus Charging Board Replacement

Written By: Dominik Schnabelrauch
  • Comments: 1
Motorola Moto E4 Plus Charging Board Replacement

Difficulty

Moderate

Steps

14

Time Required

30 - 50 minutes

Introduction

Use this guide to remove the charging board in the Motorola Moto E4 Plus (XT1771).

Before you begin, download the Rescue and Smart Assistant app to backup your device and diagnose whether your problem is software or hardware related.

Before disassembling your phone, discharge the battery below 25%. If your battery is swollen, do not heat your phone. Swollen batteries can be very dangerous, so wear eye protection and exercise due caution, or take it to a professional if you're not sure how to proceed.

  1. PCCXuPCwmVpwtTCZ
    PCCXuPCwmVpwtTCZ
    bPy2yicrAdZxADOP
    2lalNWm6HLMBs6AH

    • Power off your phone before beginning disassembly.

    • Insert the edge of the spudger into the notch on the bottom right corner of the phone.

    • Twist the spudger to start releasing the back cover from the phone.

    • Slide the spudger along the bottom edge to separate the back cover from the phone.

  2. BUAOpKayenHBerHv
    BUAOpKayenHBerHv
    Hajy1vGJYVD5BJSq

    • Lift the phone unit out of the back cover.

  3. uQUf2htv3tBFguXy

    • Remove the eighteen 3.3 mm Phillips screws securing the midframe assembly.

  4. OB1nkHUu13UkPsEx
    OB1nkHUu13UkPsEx
    rBkIaTHeKhMtjbnV

    • Remove the charging board cover.

  5. qvAwQyXWkDpEM63D
    qvAwQyXWkDpEM63D
    oUeTRnhFSk3kbbsG
    pAjwAZVrCdQmOVNV

    • Remove the battery cover.

    Hoe kom ik aan een nieuwe cover of waar is die te koop.

    Antoinet -

  6. SG3BidfIJhuNVmRI
    SG3BidfIJhuNVmRI
    LW6CdknPWSEdboFQ

    • Insert an opening pick underneath the bottom left corner of the motherboard cover.

    • Slide the opening pick between the cover and the second SIM tray to release the plastic clip.

  7. dLcpNWeDPW1VGJRG
    dLcpNWeDPW1VGJRG
    UDi3hWIsviVro5EK

    • Insert an opening pick underneath the bottom right corner of the motherboard cover.

    • Use the opening pick to pry up the motherboard cover.

  8. Sc63bxRyFcvihlew
    Sc63bxRyFcvihlew
    HfOHa1LZakKp1sxy

    • Remove the motherboard cover.

  9. HBto2G6tNJGtUVDf
    HBto2G6tNJGtUVDf
    ZoFWKvCn4ZLJMlmU

    • Use the edge of a spudger to pry up and disconnect the battery flex cable from the motherboard.

  10. HySGdVerPsZJkGMl

    • Remove the single 2.9 mm Phillips screw holding the charging board to the frame.

  11. PMRQ3MWveXBlFeZ5
    PMRQ3MWveXBlFeZ5
    dsj2kLKUV2IkICrl

    • Use a pair of tweezers to pry up and disconnect the antenna cable.

  12. UM5RSZMqasMYxqDm
    UM5RSZMqasMYxqDm
    N6iTYUYaVfVnCsHf

    • Use the edge of a spudger to pry up and disconnect the interconnect flex cable.

  13. ZUtYWRRGn22FSGjR
    ZUtYWRRGn22FSGjR
    w4UZWvjaQXIR1RUE

    • Use the edge of a spudger to pry up and disconnect the fingerprint sensor flex cable.

  14. RdFBHVRYgQ6nCtTS
    RdFBHVRYgQ6nCtTS
    cvh4UkSQpfnOiRGg

    • Insert the tip of a spudger underneath the bottom edge of the charging board and pry upwards.

    • Remove the charging board.

    • Before reassembly check your new part for any components that might need to be transferred from the old one (e.g. microphone rubber gasket).

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Dominik Schnabelrauch

Member since: 23/11/16

176120 Reputation

0 comments