Panasonic SA-PM17 Tape Player Cover Replacement

Written By: NathanB
  • Comments: 0
Panasonic SA-PM17 Tape Player Cover Replacement

Difficulty

Moderate

Steps

15

Time Required

45 minutes - 1 hour

Introduction

This guide will show you how to replace the tape player cover of your Panasonic SA-PM17. The tape player cover protects your cassette tape in the device. Cassettes are not used very much anymore however they are fragile media and it's recommended that you use the tape player with a cover.

  1. UXeV6UTrAjrgcVWM
    UXeV6UTrAjrgcVWM
    6PU2ZRGvfvwlo4NS

    • Using a philips screwdriver, remove these eight 9.5 mm screws on the left and right sides of the device and place aside.

  2. Yil6Lh4m1fEIAvZe

    • Remove these five 11.5 mm screws and place aside.

  3. Py5ISLnOSxCTDrNd

    • Lift the right side off of the device and place aside. Repeat for left side.

  4. peyt6cuJRtKfVpSG

    • Lift the top of the device gently but firmly from the back part until fully detached.

    • Allow the top to rest on the back without reattaching it.

    • CAUTION: Do not lift the top too far as there are wires attached to it.

  5. hIiiJOS6JBEfuL1c
    hIiiJOS6JBEfuL1c
    Btg4PdU5jTaQuZYP

    • Lift up on the tabs indicated to disengage them from the hooks holding them in place.

  6. gHuEreWGeDYD53mS

    • Lift the top up while firmly sliding it towards the back of the device.

    • CAUTION: Do not lift the top too high as there are cords that need to be detached before the top can be removed.

  7. A2m4AMlLkSbmLh3l
    A2m4AMlLkSbmLh3l
    tIfNEODcJJlqjM4r

    • The second picture shows a close up of the region indicated in the first picture.

    • Remove the small black wire indicated. Grip the wire near its base and pull gently but firmly until it pops out of the slot.

  8. hVxycHVf3JFYh3Nk
    hVxycHVf3JFYh3Nk
    BQo4KJ3Bkefqf3QL
    qXVumpZms6cSGlTx

    • This step deals with the indicated area of the device.

    • Using fingers or tweezers, lift the indicated tabs out until the cord's restraint looks like the final picture.

    • Gently pull on the cord near it's base until it comes free of the restraint.

  9. VnNqQq2kUlLpvqt2
    VnNqQq2kUlLpvqt2
    rjMUDSROvbBTmk5L
    LkNw4PPuHobjxhZl

    • This step deals with the indicated area of the device.

    • Lift the indicated tabs out until the restraint looks like the final picture.

    • Gently pull on the cord until it comes free of the attachment.

    • The top section of the device should now be free of the body.

  10. gsWDlsLgoFJJSFc1
    gsWDlsLgoFJJSFc1
    taMiBjYxVRAIteQX

    • Remove the four indicated 12.1 mm screws and place aside.

  11. CnyqvFMvUpJCKRCP
    CnyqvFMvUpJCKRCP
    xWgWNlfMStO4NIae
    QOOfWXWGHKsqlfLe

    • This step deals with the indicated area.

    • Using fingers or tweezers, pull the indicated latch to the right to disconnect the tape player unit from the top of the device.

    • While holding the latch to the right, lift the unit up from the plastic.

    • CAUTION: When the latch is disengaged, the tape cover may push out and force the rest of the apparatus to pop up. This is normal, but be careful that the tape cover does not pop out too quickly.

    • NOTE: When placing this unit back on the device, you don't need to follow this step, you can simply push the unit into position and the latch will automatically snap into position.

  12. F3hJLfYvLhbkAQit
    F3hJLfYvLhbkAQit
    Z5bnTwUSotF3JSLJ
    WcUXpqQSpsyRWj2k

    • Using your thumbs, push the casing forward.

    • Note the position of the tabs in these pictures.

    • Once you've slid the case forward, it should come loose to remove.

  13. QhDPHNHjw2JiVS2H
    QhDPHNHjw2JiVS2H
    sfAC6xQHVKNtNohd
    aMwVVuAFOdOtCXcF

    • Pull back on the peg while pulling forward on the tab until the peg comes out of its hole.

    • Lift the peg up and allow it to rest on top of the casing, as indicated.

    • This step requires some force.

  14. VLRvKYbehsqRjRKV
    VLRvKYbehsqRjRKV
    F2sMqDfqJDZFgPRd
    L3vvgtFC6caOCMMD

    • Pull back on the peg while pulling forward on the tab.

    • Once the peg is loose of its hole, lift upward until it is clear of the tab.

    • This step will also take some force.

  15. 4GyKmOYdMZJl5ykR
    4GyKmOYdMZJl5ykR
    fm4fHLHMmlP6E43S
    QSG314bfKXntYMpu

    • Lift the cover up and out from the inside of the top section.

    • If at first the cover does not come free, jiggle it around until it does. Do not force it out.

    • Note the position of the spring and gear, then remove and place them on your new tape player cover.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

NathanB

Member since: 13/04/11

394 Reputation

0 comments