Sony DualSense Controller Rear Case Replacement

Written By: Sam Omiotek

Comments: 11

Sony DualSense Controller Rear Case Replacement

Difficulty

Moderate

Steps

Time Required

10 - 15 minutes

Introduction

Follow this guide to replace the rear case on a Sony PlayStation 5 DualSense controller.

Tools

Step 1

Disconnect and power down your controller before you begin.
Insert an opening pick underneath the middle trim at the bottom-right corner of the controller to release the clips securing it to the case.

Step 2

Slide the opening pick along the lower-right edge of the middle trim to release the clips securing it to the case.

Step 3

Insert an opening pick underneath the middle trim at the bottom-left corner of the controller to release the clips securing it to the case.

Step 4

Slide the opening pick along the lower-left edge of the middle trim to release the clips securing it to the case.

Step 5

Use your fingers to lift up the bottom edge of the middle trim to release the remaining clips.
Lift the middle trim over the joysticks to remove it.

Step 6

Insert the flat end of a spudger into the gap above the L1 button.
Cover the button with your thumb to prevent it from ejecting across the room.
Pry upward to remove the L1 button.

Step 7

Insert the flat end of a spudger into the gap above the R1 button.
Cover the button with your thumb to prevent it from ejecting across the room.
Pry upward to remove the R1 button.

to save a few bucks, the L1 and R1 buttons can be removed without the use of the spudger tool by using any thin prying tool and just pry the buttons from the bottom instead of the top

Alan Peng -

What I didn't see addressed anywhere (here or in other similar articles) is that replacement R1 / L1 buttons can be differ enough to be un-usable depending on which model your ps5 controller is. The ones I ordered don't fit and now I can't find a way to be sure I get the right ones because few know there's even a difference.

Walt Mather -

Step 8

Use a Phillips screwdriver to remove the two 6.4 mm screws securing the bottom corners of the lower case.

Step 9

Use a Phillips screwdriver to remove the two 6.4 mm screws behind the L1 and R1 buttons.

Step 10

Use the pointed edge of a spudger to unclip the two clips on either side of the headset jack.

If these are similar in nature to the DS4’s clips, don’t use too much force so you don’t end up breaking them

Strings Cat -

there is a clip that holds the rear cover in place located in R1 and L1

Zargruzski nakamura -

Is there a clip in R1 and there's another in L1? Any way to see where exactly? The part of the back cover near L1 and R2 is that one that's not coming off. I can't seem to pull it off easily the way it looks in Step 11.

tofu -

Step 11

Remove the rear case.

There are four more clips/hooks hidden in the seams along the outer sides of the handles. If you pull open the controller as shown in this step, then you will shear off the two tiny clips which are right next to the R1 and L1 buttons.

Therefore, you should first release those clips by prying the seams open sideways.

I noticed this with the updated design of the controller, not sure whether the hooks are present on the first version.

The hooks are not critical for the integrity of the controller as the two halves are held together by the screws hidden under the buttons. The damage does show that the controller has been taken apart.

Nick -

Thought I'd clarify: The clips next to the L1 and R1 are on the outer side from the L1 and R1 buttons, I'd suggest zooming in on the picture to see them. They're quite easy to break, but also easy to remove using the plastic spudger along the seam, bending the bottom cover outwards

Franz Rolfsvaag -

I am still strugling to find the clips. Could someone point them out in the image with a screen shot or something like that.

aGingerThing -

I keep getting stuck at this step too with the new DualSense CFI-ZCT1WA revision. The top and bottom shells seem like they are fused together next to L1/R1 but I can't seem to be able to find where these hidden clips are located. My controller is still in warranty so I don't want to break them in case I can't fix my issue.

but also easy to remove using the plastic spudger along the seam, bending the bottom cover outwards

I tried this but it seems that the you need a lot of force and I ended up bending the tip of my spudger. Are you sure it's not the top cover that you need to pry away? The bottom cover has a ridge to make sure it's under the top cover so it's not easy to bend outwards.

@samomio I think there needs to be a step added for these new clips.

robplease -