Xbox Series S Fan Replacement

Written By: Robert Boyd

Comments: 6

Difficulty

Moderate

Steps

Time Required

20 - 40 minutes

Introduction

Follow this guide to remove and replace the fan on a Xbox Series S.

Tools

Parts

Xbox Series S Fan Assembly

Step 1

Before you start this guide, turn off the Xbox and unplug any cables from it.
Use tweezers to peel off the two white screw covers located on the bottom corners of the back panel.

Where can I get a shell replacement?

King DK -

Step 2

Use a T8 Torx driver to remove the two 10 mm-long screws securing the back panel to the bottom panel.
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Step 3

Slide the bottom panel horizontally toward the back of the console until it comes to a stop.
This slides the clips out of the slots on the plastic case.
Lift straight up and remove the bottom panel from the plastic case.

Step 4

Use a T10 Torx driver to remove the seven 51 mm-long screws securing the chassis to the plastic case.

Step 5

With the bottom of the Xbox facing you, pull the two bottom-rear corners of the plastic case away from each other.
As you pull the corners apart, slide the back panel towards the bottom of the device. This releases the back panel from the plastic case.
The back panel should now settle on top of the clips on the back of the plastic case.
The back panel is permanently attached to the aluminum chassis.
Do not attempt to fully remove the chassis from the plastic case with this technique. You may risk breaking your case.

Step 6

Pull the bottom-left corner away from the chassis while swinging the chassis away from the plastic case.
You may need to lift the chassis to free it from the clips on the bottom-front of the plastic case during this process.
Remove the plastic case from the chassis.

Step 7

Use a T10 Torx driver to remove the seven 11.3 mm-long screws securing the power supply to the chassis.

Step 8

Flip the device over.
Lift the upper chassis straight up to remove it.

Step 9

Lift the power supply straight up to disconnect it from the motherboard.
Remove the power supply.

Can you please tell whether it is indispensable to use the power supply with exactly the same Revision, S/N and P/N or is the same model number, like 1920, 1921 enough to make it work? Thanks for showing the teardown.

Ali Taimoor -

Step 10

Use a T10 Torx driver to remove the two 11.3 mm-long screws securing the fan to the chassis.

Step 11

Flip the device over.
Take care when flipping the chassis over because the fan is now loose.
Use your fingers to pull and disconnect the fan connector from its motherboard socket.
Take care not to pull on the wires when disconnecting the fan to prevent breaking the connector.
This connector may be difficult to remove. A good method to remove it is to shimmy the connector up and out of its socket with a spudger.
You may be able to remove this connector without removing the power supply with a pair of needle-nose pliers.

If you are careful you can also remove the connector by lightly prying from the sides of the connector in equal proportions (left then right then left etc.) using a 2.5 flathead.

Zachary Stensrud -

my fan was solder to my board but it broke off i have no idea ho to put it back my power button is missing the power button on the board i need help

Edwinn du Plessis -

Step 12

Lift the fan straight up to remove it from the motherboard.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Author

Robert Boyd

Member since: 01/02/21

23303 Reputation

2 comments

what kind of pin connector does the fan use? i want to see if it’s possible to attach a fan splitter y cable.

Sir Yeeks -

Hi wondering if I’m able to switch out the fan to another fan like a noctua fan but I don’t know what fab size?

bp.guevara87 -