Bose QuietComfort 35 Repairing the power button slider Replacement

Scritto Da: Pieter van der Wolk
  • Commenti: 7
Bose QuietComfort 35 Repairing the power button slider Replacement

Difficoltà

Moderate

Passi

5

Tempo Necessario

40 minuti

Introduzione

The slider button had a part broken off; this manual describes glueing it in place.

  1. MfCIKYYYUmofIWAb

    • These Bose headphones have a power slider on the bottom shell in the picture. After 3 or so years, the slider no longer engages, and after disassembly it can be seen that a part of the slider has broken off. This can be fixed with glue and a heat-shrink tube.

  2. CTUvQjVnLnAiBqyb
    CTUvQjVnLnAiBqyb
    TefFvb1KnXAQvb2Q
    1nBRW6WmmKQG4GMl

    • ... as seen on Youtube: remove the earpads by gently pulling, they are held in place by clips.

    • Then remove the cloth; it has been glued, but can be pried off. Opening a single edge is sufficient to find the three screws.

    • Minor tears are no concern; in this case when reassembling, double sided sticky tape has been used.

  3. XLWDUXQuRFFWxjZ2
    XLWDUXQuRFFWxjZ2
    CBe2ETHujPElTAYR
    XCZnug6UB5ANixL3

    • The shell is held in place by three phillips screws, see photos. Then the shell at the back can gently be pried off.

    • it may be helpful to use tape to pull the shell. Whilst opening, the power slide and the bit that broke of fell out.

  4. JDiTWBPODV1P6Epq
    JDiTWBPODV1P6Epq
    ayXGsqGJnCYjkM4f
    WyVOnIUk6LajmGMQ

    • Glueing the broken part in place with instant glue restores the shape; here an additional heat shrink tube has been added for extra strength.

    • Gently heat the tube so that it pulls the part in place.

    • Also, the instant gluemade the opening a bit more narrow than original, so some smal torx have been used to widen the hole a bit. A very small drill would work as well.

  5. mJqg2lMUXnhTOXqA

    • Place the sider back, where the knop is oriented towards the centre of the headphone shell.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Pieter van der Wolk

Membro da: 09/01/23

832 Reputazione

7 commenti

This fix in this video is not very well done. Not explained well enough!

Marly Marls -

Let me know where you get stuck, and what you miss.

Pieter van der Wolk -

Hi, can I get a quick repair from you with pay if I come to your location? Please give me your number

Zehal Khosraw -

I recommend repair café's https://www.repaircafe.org for that, I volunteer in one.

Pieter van der Wolk -

Do you have a part number for the power switch or offer a replacement? My Quiet Comforts turn themselves on intermittently so I often find the battery dead when I need to use them.

maginhome -

In my headphones, a pair of first-generation Bose QC 35 headphones, the power switch looks to be a C&K JS207011SCQNR.

https://www.ckswitches.com/products/swit...

It's a gull wing leaded, dual throw, 3-position switch (DP3T).

Seppe Stas -

In my case, the switch itself broke (the plastic bit broke off). I repaired it by sticking a needle heated with a lighter in the plastic and using some wire insulation to add some padding. It's not a perfect fix, but it should hold until I get my Digikey order with a replacement switch.

Seppe Stas -