HP Chromebook 11 G3 Camera Replacement

Scritto Da: Rahul Goyal
  • Commenti: 1
HP Chromebook 11 G3 Camera Replacement

Difficoltà

Moderate

Passi

15

Tempo Necessario

10 minuti

Introduzione

This guide walks through replacing a faulty camera. It requires removing the keyboard mount and lid. Afterwards, this guide requires a plastic opening tool and recommends tweezers to finish removal.

  1. kTLULoYvMWqxSApe
    kTLULoYvMWqxSApe
    3SOKsBJG3UuYRUqV

    • Flip the laptop upside down so that the lid lies flat on the table.

    • Remove the nine 6mm Phillips #00 screws that line the border.

  2. IRvkHp1aoqI5CyxA
    IRvkHp1aoqI5CyxA
    aKVyGerKYkgCL4vS

    • Remove the two rubber feet closest to the hinge using tweezers.

    • Remove the two 6mm Phillips #00 screws revealed under these rubber feet.

    • The rubber feet may tear while removal; preventing this can be difficult, but it won’t harm the laptop. If desired, replace these rubber feet during reassembly.

  3. LwgQFOUvVTgHQmfb

    • Flip the laptop so it is in the upright position.

    • Open the lid.

    • Unsnap the keyboard mount along the border of the laptop using a plastic opening tool.

    • This may require more force than expected. Hearing loud clicks as the plastic opening tool slides along the seam is normal.

  4. OyWy1LvdO12ZS4Ai
    OyWy1LvdO12ZS4Ai
    EETTmIjp6aXyiWw4
    w3kqSSplRh5kIxZi

    • Tilt the keyboard mount up.

    • Use a spudger to flip up the two ZIF connector retaining flaps for the ribbon cables that connect the keyboard mount to the motherboard.

    • Gently remove both ribbon cables.

  5. LFTxR4CXnvnHvpou

    • Lift the keyboard mount out of the laptop.

  6. noCKSQDXOjbNLvGU

    • Gently tug on the black and white wires connected to the Wi-Fi module to disconnect them.

  7. dRDlFTaBCyxPcDQJ
    dRDlFTaBCyxPcDQJ
    HPEKFuLj1AmdIxF2

    • Using a spudger, lift the ZIF retaining flap that secures the display’s ribbon cable to the motherboard.

    • Gently pull the ribbon cable out of its socket.

  8. EoPjZZUxl5Z4PHhC

    • Free the wire from the casing.

  9. aocScLOZybRtu1IZ

    • Remove the two 6mm Phillips #00 screws located near the upper left and right corners of the hinge mounts.

    • Hold the lid so that it is folded slightly inwards while removing the screws so that the lid doesn’t fall.

  10. RIg6I3YGM1fSFjaM

    • Rotate the lid to a 90-degree angle with the table.

    • Shimmy the lid out of the laptop.

  11. a3yNViMgQG4FiPQa
    a3yNViMgQG4FiPQa
    wUELwbThe1RFwGsb
    JCTcXWiE6SSEB6bH

    • Use the plastic opening tool to pry the left and right side of the top of the lid, and proceed inwards from the sides.

    • Do not attempt to remove the entire frame; this isn't necessary for removing the camera.

    • Do not pry at the center of the lid; this may damage the camera inside.

  12. GidTTmO1MlXoKLNl

    • Gently remove the slide-out connector near the bottom left corner of the camera mount.

  13. kManJFYqxKmHH3HN

    • Locate the two silver strips of tape on each edge of the camera mount.

    • Use tweezers to peel off these strips.

  14. nARUbtvefnJb5ZAK

    • Use a plastic opening tool to pry the camera mount out of the lid.

    • Apply force evenly to prevent bending the mount.

  15. CBJkUxFRLhyfMTI5

    • Lift the camera out of the lid.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Rahul Goyal

Membro da: 26/04/17

1369 Reputazione

0 commenti