HP Pavilion dv6700 Heat Sink Replacement

Scritto Da: Alec Gramm

Commenti: 4

HP Pavilion dv6700 Heat Sink Replacement

Difficoltà

Moderate

Passi

Tempo Necessario

15 - 20 minuti

Introduzione

If your HP pavilion dv6700 is producing excessive heat or the fans are very loud it most likely means that your heatsink is broken and you need to replace it. The heat sink works by attaching to a computer chip and absorbing the heat it produces, cooling it down and preventing the chip from overheating.

Warning: make sure to power down your device and to wear anti-static guard straps as you could damage the circuitry when coming into contact with static electricity.

Strumenti

Passo 1

Flip over the device so that the bottom is facing you.
Locate the battery on the bottom of your laptop.

Passo 2

Slide the tab all the way over to the left until battery pops out. Lift out and remove battery.

Passo 3

Remove the RAM port cover by unscrewing the two screws.
These screws can not be fully removed because they’re captive. Loosen them until they turn freely.

Passo 4

Use a Phillips #00 screwdriver to remove the two screws securing Hard Disk Drive (HDD) cover.
Screws will not fully remove. Loosen them until they turn freely.

Passo 5

Use a Phillips #00 screwdriver to remove the 25 screws securing the bottom of the computer.

Passo 6

Detach WiFi antenna wires.
Be sure that the wires are labeled so you remember which ones go where.

Passo 7

Using the Phillips #0 screwdriver remove the 2 screws.
Use a needle-nose pliers to do the initial loosening, then switch to using a hex screwdriver (size 5) head to do the rest of the loosening.

Passo 8

Flip over HP Pavilion dv6700 so that the top is facing you.
Open up HP Pavilion dv6700.

Passo 9

Use an iFixit opening tool to pry open the plastic bar above the keyboard.
Be careful not to yank so hard that you rip out the ribbon cables underneath. There is enough room to pull safely, but use control to prevent damage.

Passo 10

Pull out and up on keyboard to remove it.
Do not yank it all of the way out, as there is a ribbon cable underneath.
Slide the two black locks on the side of the keyboard cable connection port up to release the cable.
Grip the ribbon cable near the connection point and gently but firmly pull it out.

Passo 11

Flip over the plastic bar.
Detach the display connector.
Do not pull on the wires. Pull on the black plastic part or wedge an iFixit opening tool or fingernail between the port and the connector.

Passo 12

Detach the ribbon cables.
Pull from the area closest to the connection port gently but firmly.

Passo 13

Pull up on tape holding down wires.

Passo 14

Pull up on the WiFi wires and out from under the metal tabs.
Do not yank them out. Let them hang loose once they are out from under the tabs.

Passo 15

Disconnect the connector from the port.
Remove the wire from under the metal tabs.
Let wire hang loose after removing under the tabs.

Passo 16

Use a Phillips #00 screwdriver to remove the black screw located in the top right corner near the display.

Passo 17

Pull upward on the screen connector tab.
It will be firmly secured, so don't be afraid to use a little extra force to pull it off.

Passo 18

Use a Phillips #00 screwdriver to remove the black screw securing the screen.
Keep your hand on the screen to secure it, as once you remove this screw, it will come loose.
Lift the screen off and set it aside.

Passo 19

Unscrew the black screw in the top right corner using the Phillips #00 screwdriver.
Pull up on the top piece and remove it.

Passo 20

Remove the screw in top left corner using the Phillips #00 screwdriver
Remove the five screws that are located on the motherboard cover.
Pull up on the cover to remove it.
You can use a plastic opener if it is hard to get your fingers under the cover's edges.
Do not pull hard on the cover, as there are two ribbon cables under the cover connected to the motherboard.

Passo 21

Pull gently but firmly on the ribbon cables at the connection points to remove them

Passo 22

Remove the four screws from the ExpressCard component using the Phillips #00 screwdriver.

Passo 23

Remove ExpressCard component by sliding it out.
Remove Optical Drive by sliding it out.

Passo 24

Detach connector from the motherboard.
This piece is likely to be very hard to disconnect, so do not be afraid to use more force than normal.

Passo 25

Using the Phillips #00 screwdriver, remove the one screw near where the ExpressCard component was.

Passo 26

Lift up motherboard.
Detach the motherboard connector at the front under the motherboard.

Passo 27

Lift up and out the motherboard.
Detach the connector under the motherboard.
Remove the motherboard.

come si fà a pulire o stappare le canaline in rame di raffreddamento del processore?

Giorgio D'Ulizia - 24/06/17

To clean, use cotton or cotton swabs with isopropyl alcohol. Be sure to let it fully dry before putting back together.

Google translate English to Italian: Per pulire, utilizzare cotton o cotton fioc con alcol isopropilico. Assicurati di lasciarlo asciugare completamente prima di rimontarlo.

Alec Gramm - 07/02/22

Sir mother board of a dv 6000 and dv 6700 the same?

Fernando -

I do not believe that they are.

Alec Gramm -

Passo 28

Using a Phillips #0 screwdriver unscrew the 5 screws located on the mother board.
The screws will not come out of the heat sink - just out of the motherboard.