HP Spectre x360 13-aw0xxx Fan Assembly Replacement

Scritto Da: Maxwell Francesco
  • Commenti: 0
HP Spectre x360 13-aw0xxx Fan Assembly Replacement

Difficoltà

Moderate

Passi

10

Tempo Necessario

20 - 25 minuti

Introduzione

Is your HP Spectre x360 13-aw0xxx overheating, making odd noises and/or freezing up? If you said yes to any of these symptoms then you might need to replace your fans. Follow this step by step guide to show you how to replace your fans.

  1. kQGRUrqTCZjhaHyn
    kQGRUrqTCZjhaHyn
    PZvTDEvuEx5braCb

    • Remove the following screws securing the lower case:

    • Four Phillips #00 6 mm screws

    • Two T5 Torx 3 mm screws

  2. SQAjx4mMHoAwMSCv

    • Insert an opening tool in the seam between the lower case and chassis.

    • Pry around the perimeter until the lower case fully releases.

    • Remove the lower case.

  3. kduPsBpHAGi2wfqo
    kduPsBpHAGi2wfqo
    ereKkyBUu1xQdZl2

    • Use two opening tools, one on either side of the battery plug, to slowly pull the plug straight out of its port.

    • Alternatively, use your fingernails.

  4. JXlIdePWOILhNsIj
    JXlIdePWOILhNsIj
    lkLTEES1kmY2TNdh

    • Use a Phillips #00 screwdriver to remove the six 2.5 mm screws securing the battery.

  5. nHlaXih4TUpXY1DB
    nHlaXih4TUpXY1DB
    JjK5cSaFTCPwpVn3

    • Carefully lift the edge of the battery with an opening tool.

    • Lift the battery up and out.

  6. ouBaGrwhejOl5UWt
    ouBaGrwhejOl5UWt
    VcduxGYV6HXkGsT2
    umBpSjkIno2WSPlq

    • Remove the black film around the fans.

  7. OEXbXTlpkt6gm6e2
    OEXbXTlpkt6gm6e2
    Y2PjkwSsPeWR3WgF

    • Remove the two Wi-Fi card antenna wires using a small pry tool.

  8. C4DGHoHXGIpkCMWJ
    C4DGHoHXGIpkCMWJ
    fuAX2GtmxufR5AVY

    • Remove the eight 3 mm Phillips #00 screws securing the fan assembly.

  9. EvBZYIh3IJRsrPCR
    EvBZYIh3IJRsrPCR
    ZMCdMfLLAUK5SnQM
    EPmr4PAvebBaVFbs

    • Disconnect the two fan cables using a small pry tool.

    • Be sure not to rip the wires, as they are fragile. It may help to slightly pry on the fans while disconnecting the wires, so the pry bar has enough room.

  10. cNsPFRXvEiOpaHfR
    cNsPFRXvEiOpaHfR
    TVGlrhDLWOMEZd4f

    • Use an opening tool to gently lift the edge of the fan assembly.

    • Lift the fan assembly up and out.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Maxwell Francesco

Membro da: 14/02/23

575 Reputazione

0 commenti