Installazione del disco rigido nell'iMac Intel EMC 2266 da 20"

Scritto Da: Walter Galan

Commenti: 12

Installazione del disco rigido nell'iMac Intel EMC 2266 da 20"

Difficoltà

Moderato

Passi

Tempo Necessario

Nessuna stima

Introduzione

Rimozione del disco rigido.

Strumenti

Spudger

Passo 1

Per rimuovere la staffa del disco rigido, premere la parte centrale contro il lato del disco, ruotando il bordo superiore sinistro verso di sé.
Dopo aver liberato il bordo sinistro, ruotare la staffa verso il bordo destro del disco rigido.
Sollevare la staffa del disco rigido dal case.

Prying the plastic bar that locks the HDD into place was probably the most difficult part of the operation, for me. It just didn't want to let go, and until you've actually removed one, it's not exactly clear how it's holding on. The left side basically has a thin wedge on the back that wedges in between the rubber grommet and the mounting bracket

modsolok - 31/03/17

Thank you for this tutorial. I tried and tried and could not get the drive out. Found this tutorial and this comment too and it was a tremendous help! My iMac 24 (March 2009) hard drive was quite stubborn to remove but I finally got it!

TAPTRONIC - 17/10/18

Actually this step is quite easy, provided you follow exactly the instructions presented here. :)

Marius Zota - 05/02/21

Passo 2

Se presente, rimuovere il pezzetto di nastro che copre i cavi del sensore temperatura del disco rigido e dell'unità ottica.

If there is some clear tape holding the excess play in the HDD thermal sensor wire, against the body back, peel it up to free the wire and give yourself as much free play as possible. When reassembling, tape back to the body.

Brian Tsai - 14/08/15

Mine was completely different. There was some black foam with the sensor underneath, held in with a plastic bracket that is attached (glued?) to the hard drive.

Joey Johnston - 16/12/19

Passo 3

Scollegare il cavo del sensore termico del disco rigido dal connettore femmina sulla scheda logica.
Durante la rimozione del connettore, può essere utile premere con i pollici le linguette sui lati del connettore verso la parte superiore dell'iMac.

I found it was not necessary to do this step if you do step 20 first - i.e disconnect the temperature sensor cable from the hard drive, but not the logic board

HBloomfield - 12/03/15

As HBloomfield said, you do NOT have to remove the sensor from the iMac body. Instead, remove the sensor from the HDD while it is still connected to the body.

If the sensor is covered with a 4mm black foam square, use your index fingernail to scrape off one of the corners where there is adhesive. If you pull on just the foam part, it will tear the foam.

Brian Tsai - 14/08/15

Passo 4

Ruotare la parte superiore dell'unità verso di sé, quindi sollevare il disco rigido direttamente dai piedini inferiori.
Il disco rigido è ancora collegato mediante i cavi SATA.
Durante la reinstallazione del disco rigido, fare attenzione a non premere gli anelli di tenuta in gomma attraverso le aperture del case con i piedini inferiori del disco rigido, poiché per recuperarli potrebbe essere necessario rimuovere la scheda logica.

Passo 5

Inserire l'estremità piatta di un inseritore fra il cavo dati SATA e il bordo del disco rigido.
Ruotare l'inseritore per separare il cavo dati SATA dal disco rigido.
Scollegare il cavo dati SATA dal disco rigido.
Ripetere la procedura per il cavo di alimentazione SATA.
Sollevare il disco rigido dall'iMac, facendo attenzione a non incastrare il cavo del sensore termico.

I honestly didn't find the spudger to be necessary for most of this replacement. It is a nice little tool that makes one or two steps easier, but it is far from necessary. I imagine an old stylus you may have laying around would do just as good a job. I would definitely suggest putting the iMac on it's stand straight up to remove the hard drive bracket from it's post, as it sits very tightly in there. I found it popped out a LOT easier on it's stand than laying down, which was next to impossible. You do have to do some careful manuevering with your partner in order to accomplish this, but it's worth it. Take it slow.

Len -

When replacing, the SATA data cable did not extend to the new drive.

Nathan Suri - 25/12/15

THIS. A hundred times THIS. I wanted to put in an SSD, and was miffed to see that the SSD was to be placed in the middle of the 2.5" to 3.5" adapter. Unfortunately, that means that the SATA cable did not reach. I tried three different adapters, all the same. I even tried to BUILD an adapter myself from flat pieces of metal (I wouldn't recommend it). In the end, I got a SATA extension cable and simply taped the SSD into the case where the HDD used to be. We'll see if any problems crop up. Since it's very light though and doesn't produce much heat I don't think there should be a problem.

Wolf Dapp - 09/04/16

You will need a dock that puts the connectors in the same place if you want to use an SSD. I've had decent luck with the Icy Dock.

maccentric - 29/04/16

I have stopped using brackets for most SSD replacements. I bought some circular hook and loop dots with strong adhesive and merely velcro the drive to the case. The cables are long enough to allow the drive to sit flat against the case if you turn the drive upside down after attaching it. Otherwise, the data cable is too short. SSDs are so light that there is no reason for over-engineering the attachment. Most tape is not strong enough but two velcro dots work great.

Greg Worrel - 16/04/19