JBL Pulse 3 LED Light Display Replacement

Scritto Da: Kaitlyn Greenfield
  • Commenti: 12
JBL Pulse 3 LED Light Display Replacement

Difficoltà

Moderate

Passi

13

Tempo Necessario

15 - 20 minuti

Introduzione

The LED light display is located on the inside of the JBL Pulse 3, under the outside casing. It LED light display is lined with LED light strips along the circular base.

  1. osRpQQvEWALbUHPS

    • Lay the JBL Pulse 3 on its side as shown in the picture.

    • Use a plastic opening tool to lift the top right corner of the speaker grill. A small amount of force is necessary to remove the grill.

  2. 1R1PXMIT3pcCltKR

    • Repeat step 1 for bottom right corner of speaker grill.

  3. ZPrneUi6ysiqEHCt
    ZPrneUi6ysiqEHCt
    pvuTAto4nieRIobv

    • After pulling the right side of the grill off, place thumb underneath grill as shown in the picture.

    • Lift and pull straight out to pull grill off the posts.

    • Repeat steps 1-3 for the left side of the speaker grill on the JBL Pulse 3. The speaker grill should now be completely removed from the JBL Pulse 3.

  5. pPNUxvn3dlSdQ6gC
    pPNUxvn3dlSdQ6gC
    WkWxPqFQRGjHWgpc

    • Use a Phillips #00 screwdriver to remove the six black 6mm screws on the inside of the top of the bottom section.

    #00 not required, successfully opened with PH#1

    Stephen Hoefler -

  6. VIiDV24dAPtBc2F2
    VIiDV24dAPtBc2F2
    JQLpKrOVMKxMaGUY

    • Turn the JBL Pulse 3 right-side up and unscrew the top ring of the device. A small amount of force and/or a cotton cloth may be necessary to remove this piece.

    Ca I Specifically buy the top ring

    Julian Cruz -

    I've the same concern as the comment above, can I buy the top ring separately?

    Yousef -

    Opening is not as simple as demonstrated in Step 6. I have followed everything through, am I missing something?

    Kusala Kumsinda -

    Is there any other place to get this part? It doesnt ship to the UK

    Amelia -

  7. hno3axXOu3AGhB2f
    hno3axXOu3AGhB2f
    A11jYshJ2XpGh4At

    • Remove the six 5mm screws on top of the JBL Pulse 3 with a Phillips #0 screwdriver.

  8. KMRDVvI2aPOSZYua

    • Pull off the top disc of the JBL Pulse 3.

  9. NNnR2JSeLtZPSlfX
    NNnR2JSeLtZPSlfX
    y1BCuvZYxdoEQIHK

    • Remove the five 7mm screws on the inside of the JBL Pulse 3 with a Phillips #1 screwdriver.

    This phase could be difficult. Try to “twist” the speaker to have a little gap between both parts and insert gently a screwdriver or opening toile to spread the gap.

    Richard Devos -

  10. nIK52M34UtlSjWZ5
    nIK52M34UtlSjWZ5
    DTBHmnflqLbCK6De

    • Peel off black, taped-on electrical lead from the inside side of the JBL Pulse 3.

  11. lOwF4QFNlbNe6vBm

    • Pull the top section of the JBL Pulse 3 up. The outside casing to the JBL Pulse 3 should now be removed.

  12. MHMpCYn1u4fjYHBp
    MHMpCYn1u4fjYHBp
    WOEpECyMnDGliXab
    OAlFewuQPJGSbIKT

    • Use a Phillips #2 screwdriver to remove the six 11 mm screws that circle the bottom of the LED light display.

    • Pull the LED light display off of the JBL Pulse 3 base.

  13. OBiM1Qt6KKsK2MHU
    OBiM1Qt6KKsK2MHU
    bVcly1VEaSDPVdvy

    • Use tweezers to pull the five connections off of the LED light display.

    up to step 13, the battery replacement steps are the same.
    From step 14 the steps change.
    Very good instructions for changing the battery in the jbl pulse 3 can be found here:

    https://www.youtube.com/watch?v=MpznDgxg...

    Mike Miker -

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Kaitlyn Greenfield

Membro da: 20/09/18

1134 Reputazione

4 commenti

Hello,I really need some code to show me how to initialize and LED display and how to output data from it.Any help is much appreciated.

Osama Siddiq -

Wow jbl

Gyyzhuahyz8yus

Majd Tom -

Where to buy the leds?

mj.viana1993 -

Hello i need an assitance in a LED screen manufacturing

volkanoo -