LG Refrigerator Model LFX25973 Refrigerator Light Replacement

Scritto Da: Bill Gilbert
  • Commenti: 0
LG Refrigerator Model LFX25973 Refrigerator Light Replacement

Difficoltà

Easy

Passi

11

Tempo Necessario

8 - 15 minuti

Introduzione

Use this guide to replace the refrigerator compartment light in an LG Refrigerator model LFX25973. The process involves removing the light unit, disconnecting it, and installing a new one.

  1. SaOfLbkeAxgmho5g

    • Unplug your refrigerator before you begin your repair.

    • If you are testing or repairing the following items, you may also need to shut off and disconnect the water supply:

    • Condenser Fan Motor

    • Compressor Motor and Thermal Overload Device

    • Water Supply Valve Assembly

  2. Go1kktiajsPNFQs4
    Go1kktiajsPNFQs4
    njmtdBTT4jfXDkUt
    OgSX5MTM1eVgCaHq

    • Open both refrigerator doors fully.

  3. RHaoJxwSdpC1kUni
    RHaoJxwSdpC1kUni
    P1in2SNQBnCSpJZD
    RiOJvHKNIuIoI6Mf

    • Lift up the front edge of the shelf to release it.

    • Unhook the shelf and remove it.

    • Repeat the last two steps for each shelf you wish to remove.

  4. Xu6AJBZC4HKLRmtF

    • Use a Phillips screwdriver to remove the two 22.5 mm‑long screws that secure the light unit.

  5. 42xT66r3lc6IIHPl
    42xT66r3lc6IIHPl
    nG6oViWqmvvQXHCp

    • With both hands, pull down the front edge of the light unit until it pops free.

    • Don't try to fully remove the light unit yet, as it is still connected to the refrigerator by some wires.

  6. usU5AT6w6U1Z5HQu
    usU5AT6w6U1Z5HQu
    d3BYWHqT6QNHlfLN
    wbHsFCSFfjJQEHhY

    • Pinch the light unit connector to release it and pull it out straight to disconnect.

    • Remove the light unit.

  7. liupNfIKtQGlIRQo
    liupNfIKtQGlIRQo
    SFoIyC4Ic6TWM5iU
    6RmbxmVF2SGKvWaP

    • Use a spudger to pry and release the two clips on the rear edge of the light.

  8. WSQkEHhSR5ohcTLw
    WSQkEHhSR5ohcTLw
    Bk3tSmjrptKIuRXm
    AO3PF6errHCLQSsK

    • Use a spudger to pry and release the sides of the light cover from the light base.

  9. PvRG2PIXfUEVZ4TJ

    • Separate the light base from the light cover.

  10. EE2WKtegbnZNOqdm

    • Use a Philips head driver to remove the two 14.5 mm long screws securing the light module.

  11. YOOKCfg2tLsJIlwc
    YOOKCfg2tLsJIlwc
    kaHOFt4ZYCoiqVR3

    • Lift the light module out of the light base and remove it.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our  Answers community for help.

Autore

Bill Gilbert

Membro da: 30/06/22

29837 Reputazione

0 commenti