LeapFrog LeapPad 32400 Speaker Replacement

Scritto Da: Aubra Sharp
  • Commenti: 0
LeapFrog LeapPad 32400 Speaker Replacement

Difficoltà

Moderate

Passi

10

Tempo Necessario

15 minuti

Introduzione

This guide will show you how to replace the speaker on your LeapFrog LeapPad 32400.

In this guide you will be removing internal components to replace or repair the speaker component for this device.

Check the troubleshooting page for symptoms to make sure this guide is the best route: LeapFrog LeapPad #32400 Troubleshooting Page

  1. NaBJZT3gPBREWAQn
    NaBJZT3gPBREWAQn
    goNBe2VPSGFOlDNA

    • Turn the tablet so the back is facing up.

    • Remove the battery covers by sliding the covers towards the sides and away from the center of the device.

  2. hWmZIq2wFDlA5PUt

    • Take out the AA batteries from both battery compartments of the device.

    • Replace batteries as needed.

  3. DfDyuVji16HQ5QIF

    • Remove three 7 mm screws using a Phillips #1 screwdriver.

    • Remove the single 6 mm screw using a Phillips #1 screwdriver.

    • Remove the single 10 mm screw using a Phillips #1 screwdriver.

  4. HdyYROoDppfKXPm3
    HdyYROoDppfKXPm3
    xb6XFORah661owmn
    wLJuWxvxTGtJweAp

    • Use a small plastic opening tool to separate the colored front cover from the white rear cover of the device.

    • With one hand on the front cover and one hand on the rear cover, start from the bottom of the device and pull the pieces apart.

    • Once only the top edge remains connected, pull the rear cover backwards away from the front cover and upwards towards the top of the device. This should release the last remaining tabs holding the pieces front and rear cover together.

    • The most stubborn tabs holding the front and rear together are along the top edge of the tablet around the game cartridge slot. This will most likely be the last area that separates, and it may require a moderate amount of force.

  5. 1OECBGAyFtUWKrGw
    1OECBGAyFtUWKrGw
    GVA2J5OIyZqRbocv
    qmxWNP53kspFEjWh

    • Separate the motherboard from the back side of the device by detaching the black and red wire connection from the back cover.

    • The two pieces that hold the pen in place will become loose. Remove and set aside for reassembly.

  6. IX5OQSYOVPPQGCup
    IX5OQSYOVPPQGCup
    cQt1jfOi13infpNO
    knuIRSrLkC41YeIJ

    • Remove the single 10 mm screw from the device using a Phillips #1 screwdriver.

    • Remove the single 7 mm screw from the device using a Phillips #1 screwdriver.

  7. BQokOUCXkl5GIMVa
    BQokOUCXkl5GIMVa
    QjYPndjWijHeMXOB
    QWgX2sOJM1fOSua4

    • Unlatch the two battery terminals using a nylon spudger.

  8. WvM1iSTL5p3p5Q41
    WvM1iSTL5p3p5Q41
    Nw4eUAsLArQlyhJR

    • Remove the single 10 mm screw from the device using a Phillips #1 screwdriver.

  9. 1KCLmI4lNEJTVRHM
    1KCLmI4lNEJTVRHM
    E3vRH5PKRtRDcVEh
    FbXIBK2DyNc5IMDC

    • Gently lift the motherboard away from the back cover.

    • Peel back the tape on the display ribbon cable connector.

    • Gently pull on the display ribbon cable and it should easily slide out of the connecter.

    • If the connector is properly open, disconnecting the ribbon cable should require little to no force.

  10. 5DnpRrkHhmfVUCXE
    5DnpRrkHhmfVUCXE
    xVym6m1NIXtVM2ky

    • Desolder the speaker wire connections at one of the two terminal locations shown.

    • Soldering requires the iron to be at hot temperatures and can cause burns. Wear safety glasses as needed.

    • Be extremely careful with the cables in this step as they could melt, burn, or break.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Aubra Sharp

Membro da: 01/03/23

457 Reputazione

0 commenti