Razer BlackShark V2 Microphone Jack Replacement

Scritto Da: Jalal Gibson
  • Commenti: 1
Razer BlackShark V2 Microphone Jack Replacement

Difficoltà

Difficult

Passi

9

Tempo Necessario

20 - 30 minuti

Introduzione

If your Razer BlackShark V2's microphone is detecting choppy, interrupted, or no audio or your microphone won't plug into the headset properly, your headset’s microphone jack may be damaged (to confirm diagnoses & solutions, see Razer BlackShark V2 Troubleshooting Page, "Microphone Not Detecting Any Sound”). This guide will assist you in the replacement of this component. Be mindful of which layers of the headset assembly you're taking apart and that you don't adversely damage the holds, small wires, ear cushions, ear cushions’ rubber linings or plastic ridges, or headset itself when applying pressure.

  1. NSApcKCUSSt4je51

    • Place the headset so that the left side is facing you.

    • The left side of the headset has the cable attachment and the volume control knob.

  2. 6mDnABgmehDcnYOk

    • Scoop your middle and ring finger underneath the top or bottom inner portion of the ear cushion.

    • You should feel a hard plastic ridge.

    • Pull from the hard plastic ridge, being sure not to pull from the soft cushion.

    • Slowly apply pressure to prevent damage.

  3. jMlPk3IXNwsbyhEm

    • Pull from the hard plastic ridge, being sure not to pull from the soft cushion.

    • Slowly apply pressure to prevent damage.

  4. cX2tgFZIqIJncQOd
    cX2tgFZIqIJncQOd
    VuyytRORClejtlGX

    • Once the cushion is removed, make sure the hard plastic base with the clips is attached to it.

    • If you are replacing both ear cushions, repeat Steps 1-4 for the other side. Then, insert the new ear cushions by lining up the clips in their respective holes and applying even pressure until they audibly click.

  5. qHKFYtUiapDuxAkM
    qHKFYtUiapDuxAkM
    FpUxEsvbQBmDngFS

    • Remove the four screws holding the speaker in the headset using a Phillips #1 screwdriver.

  6. 1sd4yqAYBeFq2h4w
    1sd4yqAYBeFq2h4w
    DI1xdmuu5GEqosjB

    • Gently grab the headset and slowly apply pressure to the speaker cover; it will come off.

    • Be careful of the wires that are attached to the back of the speaker to ensure they won't be damaged when removing the speaker and its cover.

  7. VhTo5F6tOle1fUEA
    VhTo5F6tOle1fUEA
    cSrdIRfjGPQtWZ55
    epiqUntsxkSDKCmv

    • After disconnecting the speaker from the headset, it is still connected by the wires that power the speaker itself.

    • With heat or with a sharp tool, remove the glue around the wires that connect the speaker to the headset.

    • Using the new speaker, you can reattach the wires soldering them in with existing glue.

    • If replacing internal components and NOT the speaker, you can do so without severing any wire connections; operate carefully to not sever them unnecessarily!

  8. y6pf4LBUZXJI3VAG
    y6pf4LBUZXJI3VAG
    TXH3xyl2rJMuKZXy

    • Remove the two screws securing the headphone jack using a Phillips #1 screwdriver.

    • These are the same size screws as those that held the speaker in place. Any smaller screws need not be removed.

  9. lxMcXAwQuBLXKTdR

    • Desolder the microphone jack from the daughterboard.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Jalal Gibson

Membro da: 08/03/23

277 Reputazione

Un commento

Where would be the best place to find a replacement mic jack?

KnightFury -