Razer Blade 15" (2020) Battery Replacement

Scritto Da: Clay Eickemeyer
  • Commenti: 0
Razer Blade 15" (2020) Battery Replacement

Difficoltà

Moderate

Passi

9

Tempo Necessario

15 - 30 minuti

Introduzione

Use this guide to replace the battery in your Razer Blade 15" (2020) laptop.

If your laptop dies quickly or doesn't hold a charge, it might be time to replace the battery.

If your battery is swollen, take appropriate precautions.

  1. qJWDQqq15FbdAQh5
    qJWDQqq15FbdAQh5
    sDPHcOmlqZFm6nuo

    • Allow your laptop's battery to drain below 25% before starting this repair—a charged battery may catch fire if damaged.

    • Unplug all cables and fully shut down your laptop.

    • Close the lid and flip your laptop over so the back cover faces up.

  2. QXKNhOgcEdB4IAhI

    • Use a T5 Torx driver to remove the ten 3.7 mm-long screws securing the back cover.

  3. PtFV26uPOrRw6VEB
    PtFV26uPOrRw6VEB
    RPkJusFBRyHjqORY
    MQPnpZujtwdxhPmD

    • The back cover is lightly secured to the motherboard by thermal pads. Depending on the age of your laptop, it may be easier or harder to remove.

    • Use a finger to pry up the right side of the back cover, starting at the Ethernet port cutout.

  4. 1PtL256PRaO4CCSV
    1PtL256PRaO4CCSV
    CAEGXRyIgRVAICOA
    VbZXUqMHEAQwIOx2

    • Remove the back cover slowly, as to avoid tearing the thermal pads underneath.

    • Lay the back cover down on its rubber feet to avoid damaging the thermal pads on its underside.

  5. XRkgHivDgZbisNw6
    XRkgHivDgZbisNw6
    M1LdDIrQVjLwRVnC

    • Apply a heated iOpener to the battery cable tape for one minute.

    • You can also use a hair dryer—but be careful, as overheating the battery may damage it or cause a fire.

  6. EoUPoXG31L6aRyAf
    EoUPoXG31L6aRyAf
    ykYMvaKZmhBGf2uP
    RuBuoMvcHbl6rIrs

    • Be careful not to damage the battery with your tool.

    • Use blunt nose tweezers or your fingers to peel and remove the battery cable tape.

  7. OeLTtP24eXZ1XKne
    OeLTtP24eXZ1XKne
    nG5o2urhstyEuH1u

    • Use the flat end of a spudger to push the square tab on the battery connector and slide it out of its socket.

  8. WLbScX5uHbvQKxRr
    WLbScX5uHbvQKxRr
    KR3aRNrnLblhXCqN
    gk1XsbOVOiOg3xgt

    • Use a Phillips screwdriver to remove the five 5.3 mm screws securing the battery.

    • If stickers cover any of the screw heads, peel and remove them.

  9. XFwKYQWxhyfChZ2W
    XFwKYQWxhyfChZ2W
    ofwMF2a4Q2wntmeT
    jSGALAqoWf5LtcgT

    • Remove the battery.

    • There's a delicate cable that might be adhered to the underside of the battery. If so, gently unstick it as you lift the battery.

Conclusione

To reassemble your device, follow these instructions in reverse order.

For optimal performance, calibrate your newly installed battery after completing this guide.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Autore

Clay Eickemeyer

Membro da: 19/09/22

64976 Reputazione

0 commenti