Samsung Galaxy Note5 Motherboard Replacement

Scritto Da: Arthur Shi
  • Commenti: 9
Samsung Galaxy Note5 Motherboard Replacement

Difficoltà

Moderate

Passi

21

Tempo Necessario

50 minuti - 2 ore

Introduzione

Follow this guide to remove and replace the motherboard in the Samsung Galaxy Note5.

  1. RiFZhNDBMelfMBTB
    RiFZhNDBMelfMBTB
    eiewCyIL1HxTkoEw
    vJjvmJtdAPFT1WOW

    • Insert a SIM eject tool, SIM eject bit, or a straightened paperclip into the small hole in the SIM card tray at the top of the phone.

    • Press to eject the tray. This may require some force.

    • Remove the SIM card tray.

  2. j5CRMGOcZLJD4NWA
    j5CRMGOcZLJD4NWA
    NREA1KAvHdhcIpDN
    UDcL1OuRcG5KS6vA

    • Using your fingernail, push the S-Pen button until it clicks and pops out of the phone.

    • Remove the S-Pen.

    Hola mi priblema es que meti al reves el spen en el orificio y al sacarlo pues ya no funciona …. Tiene reparacion es un galaxy note 5

    Lidia Lopez -

  3. sSRM2RKyEjFojdkT

    • If the glass back is cracked, carefully tape over the entire surface with packing tape.

    • Apply a heated iOpener to the bottom of the phone for about two minutes.

    • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

  4. kUoBHVSPhlhEPpn6
    kUoBHVSPhlhEPpn6
    tJUWShrlyZOPjPjd
    qEZhBnWKHOU65tF3

    • Apply a suction cup as close as possible to the bottom edge of the phone.

    • If the phone's back cover is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

    • Lift on the suction cup and insert an opening pick under the rear glass.

    • The rear glass very fragile and can break if you use too much force or attempt to pry with metal tools.

    Yes very fragile, i dont know how to remove without cracking the glass back.

    victor zlotnicki -

    It IS possible, because I just did it. You have to be extremely patient and use firm but gentle pressure. It took me nearly an hour just to get the back off.

    Michael Ridenour -

    One more thing: I discovered that the only way that I could get enough heat into it to soften the adhesive it is to fold the hot iOpener so that you heat from both sides.

    Michael Ridenour -

  5. mbwPJvJ2vr4R2dQj

    • Once the pick is in place, reheat the edge with an iOpener for another minute.

  6. 2j5HC2lnVrkcITIg
    2j5HC2lnVrkcITIg
    qfJtEcuDoOMrkm1v
    NABbvJp3xLyq15UO

    • Slide the pick down the bottom edge of the phone.

    • Go slowly so that the tip doesn't slip out of the seam. If sliding becomes difficult, reheat and reapply the iOpener.

    • Leave the pick in place to prevent the adhesive from resealing, and grab another pick as you proceed to the next step.

  7. nGvqmAbCWNTZZo1Y
    nGvqmAbCWNTZZo1Y
    gFXgr2kvmlo4piCH
    BRlNaYv1HiLJ1Qsv

    • Insert another pick and slowly cut around the corner of the phone.

    • Due to the curved shape of the back, the glass is extremely fragile and prone to cracking in the corners. Be patient and reapply an iOpener if the corner feels hard to slice through.

  8. Ee3VHR2uYouDKHwO

    • Before cutting further, apply a heated iOpener to the long edge.

  9. geqWV1TqxwDhvZ5T
    geqWV1TqxwDhvZ5T
    S6cCXyyOPTPHbXCT
    NQwBgqZ4cxNiF3cj

    • Repeat the previous heating and cutting procedure for the remaining three sides of the phone.

    • Leave an opening pick in each edge of the phone as you continue to the next to prevent the adhesive from resealing.

  10. XgErB2TRRO5hVZtS
    XgErB2TRRO5hVZtS
    xMBEJwfEWbh5C23n
    A4ZksKnelpOCgau4

    • Use an opening pick to cut any remaining adhesive around the edges of the glass.

    • Lift the glass and remove it from the phone.

  11. EyIoaUI3dvivjmPr

    • To reinstall the back cover:

    • Use tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.

    • Clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.

    • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

    • Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as Tesa 61395. Be aware that this leaves gaps that are vulnerable to liquid intrusion.

    • After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

    • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

  12. BtGRtBBEMmKypvfV

    • Remove the twenty 3.3 mm Phillips screws.

    the phone was gave to me and I bought a replacement battery but two of the screw around the camera won't come out it's like their stripped what do I do

    wadefultz2 -

    Hi wadefultz2,

    You can try some of these methods:

    Come rimuovere una vite danneggiata

    Arthur Shi -

  13. 34JFLSUTUNuEC4aX
    34JFLSUTUNuEC4aX
    ZGTclIdSDNpTHJeP
    cIjECLOZdrvD4KMT

    • Make sure you've ejected the SIM tray before performing this step.

    • Hold the midframe by the edges and lift it upwards while pushing down against the battery with one finger.

    • There is a small amount of adhesive in each corner holding the midframe to the display assembly. Apply constant force until the midframe separates.

    • Remove the midframe.

    During this step, I destroyed my phone. Some of the circuit board at the bottom of the battery is attached to the mid-frame. When I pushed on the battery as instructed, it broke apart. The phone is useless.

    Edward Hamilton -

    Hi Edward,

    I’m sorry to hear that! My guess would be that a stray screw held the board to the midframe. If your phone had an extra screw that I missed, please notify me and I’ll correct it!

    Arthur Shi -

  14. hLAj1hQSFxmvPvxs
    hLAj1hQSFxmvPvxs
    NfihSUeHQgd2v3kt

    • Using the flat end of a spudger, lift the battery connector straight up from its socket on the motherboard.

  15. 3koJmWh2HYRLAJcT
    3koJmWh2HYRLAJcT
    LDp1U3Y6xyQiWFmr

    • Using the flat end of a spudger, disconnect the earpiece connector.

  16. rqjbFpcfWndMsHdb
    rqjbFpcfWndMsHdb
    gYPWbFcAfjyy6QOd

    • Using the flat end of a spudger, disconnect the touchscreen connector.

  17. kgTtO44IRwVgdcar
    kgTtO44IRwVgdcar
    uHPJWe6wwirvjrLL

    • Using the flat end of a spudger, disconnect the display connector.

  18. Ww4GMRUAWVjFbchZ
    Ww4GMRUAWVjFbchZ
    ZW5xbPXhO2qa35AQ

    • Using the flat end of a spudger, disconnect the navigation buttons connector.

  19. 513MdefrOInxpIKJ
    513MdefrOInxpIKJ
    ibEQCFwmECVRbT4c

    • Using the pointed end of a spudger, disconnect the antenna cable.

  20. iecmRQx5kQge15IM
    iecmRQx5kQge15IM
    KpHCusUihrCeCuOY
    pQDRKWbJjlbj1eif

    • Holding the motherboard by the top corners, hinge it upwards while clearing flex cables out of its path.

    • Do not remove the motherboard. It is still attached to the daughterboard.

  21. HPsiBhYLt4SYgEvX
    HPsiBhYLt4SYgEvX
    mSIyrHexAIHIs6jJ

    • Using the flat end of a spudger, disconnect the daughterboard connector from the motherboard.

    • Remove the motherboard.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Arthur Shi

Membro da: 03/01/18

248236 Reputazione

Un commento

thx buddy for help

kararcoco -