Samsung RF28R7201SG Refrigerator Evaporator Fan (Refrigerator Compartment) Replacement

Scritto Da: nicO
  • Commenti: 0
Samsung RF28R7201SG Refrigerator Evaporator Fan (Refrigerator Compartment) Replacement

Difficoltà

Moderate

Passi

14

Tempo Necessario

30 minuti - 1 ora

Introduzione

This guide shows how to remove and replace the evaporator fan or circulation fan in your Samsung RF28R7201SG refrigerator.

The Samsung fridge has two evaporator fans, and this guide is for the fan in the refrigerator compartment. For the freezer evaporator fan, follow this guide instead.

The evaporator fan circulates cold air from the evaporator coils into the refrigerator compartment. If your refrigerator compartment isn't cooling evenly (the back of the compartment gets much colder), you may have a faulty evaporator fan.

  1. SaOfLbkeAxgmho5g

    • Unplug your refrigerator before you begin your repair.

  2. O2XGt1FbR2wqssVR
    O2XGt1FbR2wqssVR
    L5gfkBAXIADyme3l

    • Open both French doors for the refrigerator compartment.

  3. EZ1pcx3sRXWP5OmZ
    EZ1pcx3sRXWP5OmZ
    KSCZFQWUTJMhLEZO

    • Remove all the loose shelves and bins from the refrigerator compartment.

    • The bottom shelf is clipped in place. Follow the next step to remove it.

  4. ncCDecLMOiqwRlDA
    ncCDecLMOiqwRlDA
    x3hVWFLnaXhGByxL
    lOUYFLy52ICUKRyR

    • Two stiff plastic tabs (one on each side) secure the bottom shelf in place.

    • Press both plastic tabs firmly with your fingers and lift upward to unclip the bottom shelf.

    • If the shelf doesn't unclip, you can try using a flathead screwdriver to press each clip in.

    • Remove the bottom shelf.

  5. XeJcGVxpbG1bXROm
    XeJcGVxpbG1bXROm
    3osilVrkkDwHykuk
    lAORpBvWcLnl2XhV

    • Use a flathead screwdriver to pry and remove the top screw cover on the evaporator cover.

  6. pedZPwOTGOCjtBEo

    • Use a Phillips screwdriver to remove the four screws securing the evaporator cover:

    • Two 37 mm-long screws

    • Two 16.5 mm-long screws

  7. rngXuZCPImQScTVw
    rngXuZCPImQScTVw
    w1cnHpjLvQ5cdtcD
    tMKZ3cEVSftCFHHY

    • Grasp the right edge of the evaporator cover with your hands and swing it outwards toward you.

    • Don't try to fully remove the cover in this step, as it's connected by several wires.

  8. 2LvrUGYhYkNTHJMI

    • Squeeze and disconnect the two wire connectors connecting the evaporator cover to the refrigerator.

  9. N2c1y1McoTuqPOAT
    N2c1y1McoTuqPOAT
    uT5K6IJUesPN3AtK

    • Pull the evaporator cover towards you and remove it.

  10. EjVrxoVyhwmhJMHp

    • Use a Phillips #2 screwdriver to remove the four 18.5 mm-long screws securing the fan bracket to the evaporator cover.

  11. ytiATx4KNNLmIX3L
    ytiATx4KNNLmIX3L
    DwBoPvmJWCm1WDX3

    • Guide the fan cable from the cover clips.

    • If you have trouble getting the cable out of the clips, squeeze the clips with pliers to create a wider gap.

  12. gRtHAIPgqYV1vMeZ
    gRtHAIPgqYV1vMeZ
    IkMldZLjDT1WvSPO

    • Lift the loose edge of the fan bracket up.

  13. fdrEINSW5fBidgxE
    fdrEINSW5fBidgxE
    TqurOZwTaCLt6MFg

    • The fan is pressure-fit in place with some foam insulation.

    • Use your fingers to press the fan out of its recess.

  14. rBLZnYdfcZor5njt

    • Remove the fan.

    • During reassembly, be sure to install the fan in the right orientation: the side with the center label should face down, towards the evaporator cover.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Ask our Answers community for help.

Autore

nicO

Membro da: 14/04/15

15885 Reputazione

0 commenti