Sostituzione batteria Teenage Engineering OP-1

Scritto Da: Tobias Isakeit
  • Commenti: 24
Sostituzione batteria Teenage Engineering OP-1

Difficoltà

Moderato

Passi

4

Tempo Necessario

30 minuti

Introduzione

Niente tastiera, niente suono, facile da capire. Ma non ti preoccupare, la sostituzione è a sua volta molto facile.

Questa guida mostra come sostituire la tastiera del tuo OP-1.

  1. vxoTLiJxFDPOji5X
    vxoTLiJxFDPOji5X
    ajlj12AYLBNXKv6o
    MSgrKiNeLFhWdEpd

    • Per raggiungere le viti disposte sotto la tastiera, devi prima togliere alcuni tasti. Puoi usare uno strumento di apertura o un plettro. La prima immagine mostra come il dispositivo dovrebbe presentarsi dopo aver rimosso le chiavi necessarie (12 in tutto).

    • Per i quattro tasti più lunghi della tastiera, si deve intervenire a partire dal lato sinistro.

    • Per staccare gli otto tasti più piccolibisogna iniziare dal basso.

  2. NKEIk4cFqiaAPIDr
    NKEIk4cFqiaAPIDr
    faMO21YfJAINC3yK

    • Il meccanismo a pantografo degli otto tasti piccoli impedisce l'accesso alla vite sottostante.

    • Usando di nuovo uno strumento di apertura un plettro, si possono estrarre facilmente questi elementi.

    • In fase di riassemblaggio, accertati di sistemarli nel senso corretto, con la faccia superiore in alto.

  3. SLEyuvdxWjnDuCUg
    SLEyuvdxWjnDuCUg
    RCYV1CYSlXFdOVKE
    MpduwLQ5mTtWh4lM

    • Svita queste 12 viti con un cacciavite a croce Phillips #00.

    • Quindi basta tirar fuori le otto manopole ruotanti e la manopola del volume.

    • Ora è possibile sollevare lievemente la tastiera e disporla più indietro.

    Your missing the ribbon decoupling step, unless you skipped it because it’s such a tight squeeze to get back in.

    William “Zoe” FitzGerald -

    The concept of removing the square panels that the knobs sit on was skipped.

    Station 2Station -

  4. sq6pFjQdQhfSeR12
    sq6pFjQdQhfSeR12
    kEQZ31Y6ENYobgjN

    • Sblocca i cavi flessibili spingendo le due levette di bloccaggio nere disposte su entrambi i lati di ogni connettore.

    • Ora puoi tirare fuori i cavi flessibili e rimuovere completamente la tastiera.

    • Quando monti la nuova tastiera, accertati di aver rimosso la pellicola protettiva sotto lo schermo.

    • L'OP-1 ha una modalità per testare funzioni specifiche. Puoi accedere a questa modalità tenendo premuto il pulsante "COM" mentre accendi il dispositivo, e poi scegliendo la funzione test (2). Non c'è bisogno di completare tutti i test e puoi spegnere dopo aver eseguito quello della tastiera.

    Don't forget to add the metal parts of the new plastic keys and press the keys down until you hear a click.

    Raimund S -

    I found bring the OP-1 higher up off my work surface made installing the ribbons much easier, oh and keep the keyboard assembly parallel to the OP-1 to ensure the ribbons seat evenly.

    Stephen Holder -

    Also you have to bend the tips of the ribbons a little bit

    Al B -

    There ribbons are incredibly frustrating -- I cannot, for the life of me, lock them in place. Even after bending them, the direction of the bend itself creates tension that pulls them out of the zero insertion force connector. The black nibs do not seem to provide enough locking force. Frustratingly enough, this happens slowly over time, so usually 24 hours after I have fully reassembled the keyboard, it starts malfunctioning again. I would really appreciate some help here.

    Sébastien Barré -

Conclusione

Per rimontare il tuo dispositivo, segui queste istruzioni in ordine inverso.

Autore

Tobias Isakeit

Membro da: 31/03/14

116544 Reputazione

18 commenti

Nice guide Tobias!

Worked like a charm. My OP-1 feels brand new.

Thanks iFixit X TeenageEngineering for providing these replacement parts!

Keep it up <3

Flavius Ivancu -

Awesome guide! Thank you!!!

Jason Wasiak -

After reassembling everything I have one key ( the upper A) which retriggers the sound randomly if I press the key.

I hope that the reason is not that I put the flex cable back too loose … and i have to open it again. Anyone had this before?

Raimund S -

This happened to me constantly, only by taking the key off I noticed the tiniest amount of moisture, a mere misting, nesting in the board. it had been re-triggering randomly… Not ideal whilst constantly gigging. Seems to be triggering normally now after drying it in front of a heater. The only thing I think could of caused this is a dry ice machine I played beside a few weeks ago.

Qaiyyum Tajudin -

Perfect. Thanks :)

kristianottosen -

Did this along with with replacing the connector board and it all seems as good as new. Recommended getting the Opening Tool, Spudger and for the connector board job the Jimmy. Well done TE for providing this to option for repairs.

Toby Curnow -

Usually when a key retriggers or triggers multiple times on one press, it's because the plastic that holds the metal on the inside of the key has broken. It still sits in place, but the key would need to be replaced.

Mike -

keyboard replaced I have a new OP1 ;)

thx TE, hope you will bring connector board please !!!

Cédric Buron -

Thank you very much for the tutorial. Made me believe that I could do it. My OP1 feels brand new again.

aaa -

Is this going to be available any time soon?

Marco Luceri -

Solid guide. Solid fix. Nice to have my synth back in order :)

Scott McGimpsey -

I have a a broken scissor mechanism on 1 single key of my OP-1, but it seems like my only option to replace that tiny broken part is to buy a whole new keyboard. Wondering if someone on this thread might confirm that (or offer and alternative). Thanks!

Ben White -

Take a look at these comments, maybe this will help.

Tobias Isakeit -

Is this ever coming back? I spilled coffee on my OP-1 last year and some of the keys no longer work. I would really like to be able to fix this

:-(

Michael Forrest -

Hi Michael, we’re constantly looking to get parts back into stock. Sometimes we are limited by our suppliers. But you can use the "notify me" function so you’ll know when it is available again.

Tobias Isakeit -

Just purchased a new keyboard but have found it to be double triggering. Not sure how to return item as no return form was supplied in package.

BBaker -

Is this ever coming back?

Taka -

After installing the new keyboard a sliver of the screen edge under the outer screen is visible. Do you think the replacement is manufactured incorrectly? Or is this an error with aligning the keyboard when reinserting it?

Elliot Ashton-Stretch -