Sostituzione candela Briggs and Stratton 675 Series

Scritto Da: Andrew Saunders
  • Commenti: 12
Sostituzione candela Briggs and Stratton 675 Series

Difficoltà

Molto facile

Passi

2

Tempo Necessario

5 - 10 minuti

Introduzione

La candela è responsabile per l'accensione del carburante nel motore. Nel tempo si usurerà e dovrà essere sostituita. Questa sostituzione è abbastanza semplice e può essere eseguita ovunque in poco tempo. Ti servirà una chiave inglese del 21 lunga 5 cm per rimuovere la candela.

  1. nJQkxClUbCqh3tFj
    nJQkxClUbCqh3tFj
    4TQpaSSe6YIP3Lm1

    • Assicurati che il motore sia spento prima di iniziare.

    • Usa le mani per rimuovere il cavo della candela, Dovrebbe scattare via quasi senza fare forza.

  2. XqyX1yBexhIPky2U
    XqyX1yBexhIPky2U
    RDxg2HCTWCvj5SNw
    ZaaHGdln5nwKA3kY

    • Usa una chiave inglese del 21 per svitare la candela dal motore. Dovrai probabilmente usare una presa lunga per poter arrivare alla candela.

    • Sfila la candela dal suo alloggio con le mani.

    • In alternativa, puoi usare una chiave inglese o delle pinze per rimuovere la candela (come mostrato nella seconda immagine).

Conclusione

Per rimontare il tuo dispositivo, segui le istruzioni in ordine inverso.

Autore

Andrew Saunders

Membro da: 01/02/15

948 Reputazione

12 commenti

I have a Briggs and Stratton engine on my lawn mower but can't get at the spark plug as there is some kind of black plastic housing in front of it.

penora -

Any ideas I have a Briggs and Stratton engine on my lawn mower but can't get at the spark plug as there is some kind of black plastic housing in front of it.

penora -

pinch the front of black cap and pull off

tracy.mullen -

What size spark plug does this 675 series lawn mower take, I didn't see it listed?

Eris -

What size spark plug does this 675 series lawn mower take, I didn't see it listed?

Kymberleah -

Who wrote this nonsense?

One important step in the replacement that was neglected was checking the proper Spark Plug Gap. Should you just take it out of the pack, without checking and install it? I wouldn’t.

Also, the Spark Plug should be installed with a Torque Wrench, setting it to 180 lb-in (20nm) . . . Heating and cooling of the Head, with an over-tightened Spark Plug could cause warping and if not tight enough, then loss of compression would result.

The correct Spark Plug depends upon Briggs & Stratton Engine Model and Date of Manufacture.

https://www.briggsandstratton.com/eu/en_...

https://www.briggsandstratton.com/na/en_...

shepherds_pie -

My 675 series more floods real easily when it is cold or if after using it for a while I take a break. If the break is about 30 minutes it simply will flood and not stat again. Any suggestions?

George Wright -

What is the spark plug gap on the Briggs 190 cc 6.75 engine

Phillip -

Briggs & Stratton Replacement Spark Plug RJ19LMC you may want to include the type of spark plug gap is .030

tom_simmonds -

My Briggs and Stratton started on 2 pull everytime and now just out of the blue it starts then it dies, any idea

Rgebhart79@gmail.com -

Can't start 6.75 briggs & Stratton Brute 22 inch mover replaced sparkplug airfilter drained gas tank , new gas , fuel filter hoses fine , pulled carburetor cleaned out dissassembled , auto choke-butterfly is in closed position when cold , i havent replaced the whole carburetor kit yet, the gaskets o ring are original , carburetor bowl bolt nut & sparkplug is wet with gas there are no leaks, cant verify to .030 sparkplug gap exists on the plug, i am bewildered, please help anyone

Kevin Marek -

Same issue with mine. Have you found the problem?

Revolución Pictures -