Sostituzione del gruppo scheda logica iMac Intel 27" EMC 2546

Scritto Da: Andrew Optimus Goldheart
  • Commenti: 62
Sostituzione del gruppo scheda logica iMac Intel 27" EMC 2546

Difficoltà

Difficile

Passi

8

Tempo Necessario

Nessuna stima

Introduzione

  1. QToXknsPIYCSTjtA
    QToXknsPIYCSTjtA
    DXU5NcMYpyTbUx1t
    AUmsYLZDkyojBZqd

    • Usa l'estremità piatta di uno spudger per disconnettere ciascuno dei quattro connettori delle antenne dalla scheda AirPort/Bluetooth.

    • Prendi nota delle posizioni di ogni connettore durante la riconnessione dei cavi. Da destra a sinistra, le antenne sono connesse in quest'ordine:

    • Il più a sinistra

    • Il più in alto

    • Quello in alto a destra

    • Quello in basso a destra

    My iMac has a slightly different assembly. There are 2 - T5 torx screws holding little clamps for each cable (2 clamps per screw). Certainly more secure but another size screw to deal with…

    Greg Freeman -

    My iMac also same with Greg mentioned. need to T5 torx driver. A1419. Late 2015, Korean Version.

    Joseph Yang -

    My 2017 has long WI-Fi card, It’s It’s a M.2, cuz no remove antenna. Undo WI-Fi card fix screws and pull out card. Easy one.

    Tanya Chachanova -

    Before I disconnect the cables, I use different color sharpies and draw a different color on each one’s head & then I take a picture of the cables connected to the board. Pic is my reference of which cable goes to what connector.

    Macrepair SF -

    I have a 2017 and I agree with Tanya. There are 2 T4 screws fastening the airport card to the motherboard. It’s easier to remove these and gently pull the airport card straight up out of the motherboard while leaving the 4 antenna wires fastened. You can’t see the connector or the airport card as it’s on the back side of the motherboard but just wiggle it side to side while pulling straight up and you’ll have no problem. I’ve broken off those tiny airport connectors in the past and it’s no fun replacing them.

    Mike Jones -

    same as Greg, did with the torx t5

    Alejandro Piris Nino -

    I have a 2019 iMac and we needed to use a T4 screw

    Mike Manasewitsch -

    My late 2015 has a Airport/Bluetooth card secured with two T5 screws. After removing them you can just wiggle and unplug it from the logic board, without needing to fiddle with the antenna connectors.

    Robin Gottschalk -

    Same as the other comments, in my iMac 27” retina 2015, the WiFi/Bluetooth board is a bit longer and the 4 coax cables are fixed by 2 T5 screws…

    SURIN Dominique -

    When reassembling a removed WiFi card keep 4 antenna leads attached as mentioned by poster (tanya et al) when reassembling as you replace logic board keeping it tilted forward helps in aligning the notch on card for easy reassembly and T3 screws replacingonce card is firmly seated.

    robert -

    When reassembling a removed WiFi card keep 4 antenna leads attached as mentioned by poster (tanya et al) when reassembling as you replace logic board keeping it tilted forward helps in aligning the notch on card for easy reassembly and T3 screws replacingonce card is firmly seated.

    robert -

    Can also confirm it for a Late 2015 iMac, there’s just 2 T3 screws to remove, simple move out the WiFi/Bluetooth board and let cable on place.

    tomax -

  2. CGJiWGncy3h6LBhi
    CGJiWGncy3h6LBhi
    AMmjHYbYZUwFZ2ON
    lt2rSeOg3qUipcdH

    • Questa è una connessione molto delicata che si può rompere facilmente.

    • Ruota verso l'alto la staffa di fissaggio in metallo del cavo della fotocamera iSight.

    • Tira il connettore del cavo della fotocamera verso la parte superiore dell'iMac.

    During disassembly, I taped the cable up and out of the way, as it tends to get in front of things.

    Tony Ross -

    I recall comments here about this being particularly sensitive. I had an issue with no iSight on rebuild, however taking to bits again and seating and reseating this connector a few times resulted in the iSight camera working again (phew).

    Amuseme -

  3. kEkmLOQXrRmsOLb1
    kEkmLOQXrRmsOLb1
    QxHXQJM2Mh3W3jtv
    RSoLgeH3lYvFRMdj

    • Usa l'estremità piatta di uno spudger per scollegare il connettore del cavo del jack cuffie dal suo zoccolo sulla scheda logica.

    • Spingi delicatamente il cavo dove non dia fastidio.

    On my 2017 iMac there is a tiny little cable and connector on the motherboard that is approximately half way along the motherboard and is connected down towards the base of the case. It came free easily when I removed my motherboard but just wanted to remind people to reconnect!

    Stuart Swaffer -

    It’s the microphone cable!

    Koen van Eijk -

    This pulls straight up, towards you.

    Eric -

    I broke mine…when inserted the speaker… How do I replace the headphone jack and cable?

    mmx2000 -

    Lift upwards with the spudger/fingernail, rocking it up back and forth.

    (For those who have not seen this style of connector.)

    Mike Rehbein -

    +1 Missing the step on this 2019 iMac 27” guide to remove mic cable. It’s in other guides, just not here.

    joe -

    I cannot determine how to reconnect the headphone jack cable to the logic board. Are there better pictures anywhere that I could access?

    Ron Owens -

  4. ML1Ep2RSLLR5UAwS
    ML1Ep2RSLLR5UAwS
    psWG2c5RYc5YJLyp

    • Rimuovere le seguenti viti Torx dalla parte anteriore della scheda logica:

    • Due viti T10 da 23,7 mm

    • Quattro viti T10 da 7,4 mm

    • Una vite T25 da 20,8 mm

    • Una vite T10 prigioniera

    • Questa vite è sotto un foro nella scheda logica. Servirà un cacciavite fisso o l'estensione da 60 mm di un kit cacciaviti iFixit per raggiungerla.

    The central screw is very difficult to reach! Use a long and very thin T10 screw driver

    MrSchaeffer -

    On my late 2015 there is another T10 (approx 16 mm long) on the lower edge slightly left of the hole in the logic board giving a total of 4 screws along the bottom edge.

    Konrad Skeri Ekblad -

    I’ve also found an extra T10 in my late 2015 iMac

    luis -

    My 2017 has small flat cable and connector on logic board. And all screws are changed to T 9

    Tanya Chachanova -

    Note: the T25 spacer is behind and to the left of the logic board and below the HDD bracket.

    Tom -

    My 2017 had all T8’s, including the captive screw beneath the motherboard

    Mike Jones -

    My 2017 had 4 T8 screws along the bottom of the logic board, not 3

    greg -

    Late 2015 iMac - mine had all T8 screws and 4 along the bottom row

    Pete Mackenzie -

    On 2019 iMac

    Red = T8

    Orange = T8

    Green = T8

    Yellow = T25

    Mike Manasewitsch -

    In 2017 too.

    Andrew Gough -

    2017 here.

    IMPORTANT - note Tanya’s comment. The narrow flat cable in the middle - it’s the mic cable on a *tiny* ZIF. See Sostituzione scheda logica iMac Intel 21.5" Display Retina 4K (2017)

    Also has the extra bolt middle lower edge.

    All T8 except the yellow T25.

    Andrew Gough -

    In my iMac 27” retina 2015 all screws are T8.

    There is also an another T8 screw between the left and central “orange” on bottom of the CPU board

    SURIN Dominique -

    Just completed and removed logic board. All my screws were T6. The screw beneath is a captive screw, stays retained in the fixture after unscrewing.

    Keith Thomas -

    If I change the logic card on an imac 27’ 2020, will the computer's memory be affected?

    nizarishi -

    There is a 25T stand off that is not listed. It is not on the board but beside or underneath the yellow/red on power supply side.

    Tom Gordon -

  5. k6FT2paJ5BY4NwDA
    k6FT2paJ5BY4NwDA
    hVmRkDA1uZehusDa
    sNxFgt3qyU16WT3n

    • Il cavo SATA del disco fisso non può ancora essere rimosso, ma sarà d'intralcio durante la rimozione della scheda logica.

    • Tirare il cavo e il connettore attraverso il supporto di destra del disco fisso. Sposta il cavo sul lato destro dell'iMac, dove non interferisca con il condotto di scarico.

    Anyone know if models that shipped with only a bladed SSD have the SATA cable still inside? I’m guessing probably not, but haven’t been able to confirm anywhere.

    Jesse Mitchell -

    The cable was so stiff, I didn’t try to pull it through the bracket. Instead I removed the upper screw holding the right HDD bracket in place. Then I rotated it counter clockwise enough to just move the cable behind it and out of the way. Once I did that, I screwed the bracket back into place. I reversed the process when I put the machine back together. It’s a Torx-10 BTW.

    Kenneth Cluff -

    Excellent tip, Kenneth! I did the same, made things easier.

    Dave Hoppenrath -

    Jesse, no SATA cable inside. My iMac came only with the blade SSD and an empty HDD bay, so I have to buy the SATA cable separately.

    mveras1972 -

    the card drive cable is affixed to the heat sink with some sort of adhesive. If it is not placed back similarly, the system cannot sense the heat sink temperature, and the fan will run at full speed continuously. I used double sided tape and pushed it back in adhered position after re-attaching logic board.

    labah -

    the above should read “the hard drive cable” , not card drive (typo)!

    labah -

  6. JsYu3VsnbGxalGKw

    • Rimuovi due viti Torx T10 da 5,7 mm dalla parte superiore del condotto di scarico del dissipatore.

    My model (2015) had another screw holding the heatsink duct and a stand-off holding the whole thing attached to the back. Even gently moving the logic board almost got the duct damaged till I realised what was going on so I’d suggest to be careful and DO NOT pull the logic board if it looks like it’s still attached - most likely it is!

    Carlos Ferrari -

    Carlos,

    I am at a bit of a loss. I have a 2015 as well and removed everything else, but the motherboard is still not moving. I found the two, as shown in the picture, but can't find a third one anywhere on or around the heatsink duct. Any help is sincerely appreciated.

    Marc

    MarcW58 -

    Ditto for the 2013 27”. One extra screw

    Dave Sands -

    My model 2546 late 2012 has 2 screws on heat sink shroud. First is on left side. The right can only be accessed with board tilted out a bit.

    Michael Wright -

    I just finished disassembling a late 2017 27” Retina and for the life of me I couldn’t get the logic board to come out. What. I discovered was that there is a part of the heat sink shroud that is held in place by a stand off boss for the power supply. You will need to remove the stand off boss using a T25. Remove carefully and save for reassembly…

    David Brix -

    Same here for late 2014.

    Jamuel Starkey -

    Yes, there is a screw holding down the fan shroud it is an angled black part where the guy's left hand index finger is located in Step 56

    Carl Schultz -

  7. 3BUpXN5OrCS6neWt
    3BUpXN5OrCS6neWt
    oe21ZlOiGLCcde4R
    qkOfruJVUANY1FyU

    • Inclina leggermente in avanti la scheda logica.

    • Alzare la scheda logica direttamente verso l'alto e fuori dall'iMac. Attenzione a non impigliarti in nessuna delle sedi a colonna delle viti all'interno del case posteriore.

    You should add a step about removing the sata cable here. When following the directions in reverse I forgot to put in back on and had to remove the motherboard again.

    Ken Prows -

    If you are having a hard time removing it, you might have forgot to remove the spacer rod when you removed all the motherboard screws. In my case, it was a T20.

    Eric -

    The 2017 iMac has a small cable with a ZIF connector coming from the bottom of the machine that needs to be detached from the logic board before it can be removed.

    greg -

    I can confirm this. As i recognized the cable after i removed the logic board i had some trouble to find the spot where to plug it in.

    sebastian.wittl -

    If you are having a hard time removing it, you might have forgot to remove the spacer rod when you removed all the motherboard screws. In my case, it was a T20. This is in my late 2015 the case. Just like Eric said 11-01-2020.

    John -

    Same for late 2012. For those curious the spacer is just to the left and appears to attach to the heat sink.

    skiingjoo -

    The iMac 27” didn’t come with the PCIe SSD card so of course there wasn’t the necessary screw to mount one.

    Here is the screw to order;

    https://www.ebay.com/itm/283482947478?ch...

    What I did was find a screw that fit. Happened to be the case screw from the iFixit external 2.5” case but since that was a countersunk screw, I fabricated a washer for it.

    Mike Rehbein -

  8. CRWmZtRpjGUJer2h
    CRWmZtRpjGUJer2h
    eINrHxdsC4vUW5HA

    • Nel riassemblaggio dell'iMac, stai molto attenti all'allineamento delle porte I/O esterne. La scheda logica potrebbe essere disallineata anche se fissata con tutte le sue viti.

    • E' possibile usare una chiavetta USB o un cavo ethernet per essere sicuri che l'allineamento della scheda logica sia corretto mentre la fissi con le viti.

    To help me line up the IO ports, I filled all the USB ports on the back with thumb drives before I screwed the Logic board back down. Worked like a charm!

    Alex Grayson -

    Ugh! Wish I saw this before. I did this mod and failed to do this step and now only one Thunderbolt 3 port works at a time and the SD card has to get pushed way further to get it to read. I hate taking this thing apart!

    scolvin -

    Thanks Alex :)

    Mike Rehbein -

    iMac (Retina 5K, 27-inch, 2017) の場合、Thunderbolt 3（USB-C）ポートの位置がシビアです。

    Ethernet、USB 3ポート、Thunderbolt 3（USB-C）へ最低でも各１本（合計３本）を差し込んだままの状態でロジックボードのネジを閉めるようにすることを強くおすすめします。

    EthernetケーブルとUSBメモリの２本を挿して調整し組み上げましたが、最終的にThunderbolt 3（USB-C）が刺さらないことが後で判明し、結果組み直しをしなくてはいけませんでした。

    For iMac (Retina 5K, 27-inch, 2017), the location of the Thunderbolt 3 (USB-C) port is severe.

    It is highly recommended to close the logic board screws with at least one cable each (total of three) plugged into the Ethernet, USB 3 port, and Thunderbolt 3 (USB-C).

    I plugged in two Ethernet cables and a USB memory stick, adjusted and assembled the board, but in the end I found out later that the Thunderbolt 3 (USB-C) would not stick, so I had to reassemble the board.

    Translated with www.DeepL.com/Translator (free version)

    JapanWolf -

    貴重な情報ありがとうございました！

    Midori Doi -

    I do this job fairly frequently and I have a small box in my iMac tool kit containing a headphone jack, four USB drives, a short two-ended Thunderbolt cable and the end of a red moulded Ethernet cable to keep things aligned from the back when screwing the logic board back into place.

    I loosely screw all the screws in, then tighten them gradually, going round the board several times to make sure it lands in exactly the right position.

    John Blagden -

Conclusione

Per riassemblare il dispositivo, segui queste istruzioni in senso inverso.

Autore

Andrew Optimus Goldheart

Membro da: 17/10/09

502162 Reputazione

0 commenti