Introduzione
Se qualsiasi delle tre prese della tua JBL Charge 3 (AUX, USB, di carica) non funziona, potresti doverle sostituire. Se vuoi sostituire solo una delle porte piuttosto che l'intero gruppo, dovrai sapere come saldare. Segui i consiglio per la saldatura di iFixit per saperne di più.
-
-
Gira sottosopra il tuo speaker ed inserisci lo strumento di appertura di plastica verticalmente nella fessura sulla cover frontale.
-
Inclina lentamente lo strumento di apertura verso di te per rimuovere le quattro clip che tengono il tutto fermo.
-
Ripeti il procedimento per tutti e quattro gli angoli della cover frontale.
-
-
-
Svita le quattro viti a croce Phillips #1 da 8 mm dalla copertura del pannello delle prese.
-
Infila il tuo strumento di apertura in plastica sotto il pannello delle prese per rimuoverlo.
-
-
-
Svita le tre viti a croce Phillips #1 da 8 mm dalla scheda logica del pannello delle prese.
-
Rimuovi la copertura del pannello delle prese dalla scheda logica.
-
Per rimontare il tuo dispositivo, segui le istruzioni in ordine inverso.
15 commenti
Is there a place to buy an entire replacement port bay?
Found the whole assembly on line for 30 bucks. Or a usb port for five from jbl
Can u share a link? Need a new port bay!
Hello! My jbl charge 3 has a problem in bluetooth, I can't detect the bluetooth in any gadget. Is there anybody have an idea how to fix this?
Sometimes disassemblers forget that the first time they disassembled the item it didn’t want to give up easily: I didn’t like the forces I was having to apply at all, so I switched to two plastic prying tools per “corner” and one in-between them (total 5, you could use plectrums…) before I was happy the the forces were low enough not to break anything.
Frank Puranik -
the front grill is supposed to be first not the back the back has longer while the front has shorter clip
Water Bass Tester (Water BT) -
There are two Phillips head screws to remove before prying the cover off
jason -
Where in south Africa can I buy jbl charge3 port bay replacement
Donovan Fransman -
There appears to be different versions of the Charge 3. If you find it difficult to pry open a second side the two small screws mentioned by Jason will need to be removed but it also indicates that there will be some additional changes to this tear down that I will try to convey in the comments as well.
john Ramirez -
Sadly I damaged the latches on my charge 3. There was more to it than just prying the front cover up. First, there is a small latch on both sides that you need to push down before pulling the front cover towards you that release the clips holding the front cover in place. Pull only slightly forward because… Second, in the front cover there are 6 circular notches connected to the front cover in tue four corners including the middle corners, you need to squeeze the front cover a little bit gently removing the notches so they dont break (like mine did).
ralphkeneth_gomz -
Definitely had to watch about 10 videos and still couldn’t get it to pop out easily.. Took a look at the first picture in the next step and really took note of where the little hole that lets you through to push down the tab is. Once I took a look at that and combined the techniques I’d seen in some of the videos it finally popped off easily. https://www.youtube.com/watch?v=u7i0_nD9... I only watched the first minute of this video but it helped a good bit if anyone else is having trouble.
Rowan Darko -
How do you know if the speakers or one of them is burned or broken.. i notice that one speaker is playing much less hard then the other one.. I wonder now if maybe there is another problem with my device.. Battery problem?
Bukowski101 -