Sostituzione scheda madre Xbox One S

Scritto Da: Erik Ramazzini
  • Commenti: 40
Sostituzione scheda madre Xbox One S

Difficoltà

Difficile

Passi

15

Tempo Necessario

5 minuti

Introduzione

Questa guida è importante per poter accedere ad alcune componenti sulla scheda madre che potresti dover sostituire.

  1. AQtIBB1ZGqHTvNg4

    • Gira l'Xbox One S in modo che la parte inferiore sia rivolta verso l'alto.

  2. cI432T5plYCpwsEg

    • Comincia lavorando sul case posteriore dove c'è l'adesivo della garanzia. Infila uno strumento di apertura nella fessura tra la parte inferiore della copertura e la parte superiore forata. Quindi trova i ganci nella fessura che tengono insieme la copertura.

    • Usa lo strumento di apertura per rilasciare i ganci. Il modo migliore è fare leva per allontanare la copertura posteriore da quella inferiore.

    • Sentirai dei suoni di scatti mentre fai leva per aprire la copertura. Potrebbe essere abbastanza difficile rimuoverne la parte inferiore.

    • Potresti rompere i ganci mentre rimuovi la copertura inferiore.

    • Consigliamo di iniziare dal retro con l'adesivo della garanzia. Fai leva con lo strumento di apertura lungo il bordo posteriore finché tutti i ganci sono liberi, poi prosegui con gli altri lati. Quando tre lati sono liberi, comincia alla fine del lato opposto al pulsante sync. Fai attenzione e prenditi il tuo tempo, si separerà tutto senza danni.

    Be careful not to damage the pairing button on this part

    David -

    Important!!

    You've to start from the back corner where is the information label, because there is a main clip behind a warranty sticker

    Cristian Ramirez -

    They should add this to the guide! I didnt know that, and did some minor damage to the bottom piece where that main clip is.

    I dont mind because it's my own Xbox, but what if it belonged to a customer?

    Charles Jackson -

    They should add this to the guide! I didnt know that, and did some minor damage to the bottom piece where that main clip is.

    I dont mind because it's my own Xbox, but what if it belonged to a customer?

    💯% same opinion!

    profnussecke42o -

    This was hard! I tried using plastic pry tools, but they did not work. A metal tool did, but make sure to watch a video or two, to see what you actually are dealing with. After the videos it went quite smoothly.

    Peterdk -

    I legitimately cannot open the case where the warranty sticker is, ive tried everything, im resorting to a fork to try and open this

    Sohail ツShah -

  3. DGFtVxEdoZKRdLMd

    • Una volta rilasciati tutti i ganci, rimuovi la parte inferiore della copertura.

  4. GeIOPswgPOYsuGeJ
    GeIOPswgPOYsuGeJ
    uITOYPJDbxUgf4Lc

    • Usa un cacciavite Torx T10 per svitare le sei viti verdi da 50 mm segnate da F1 a F6 dalla copertura in metallo.

    My F3 isn't coming out. The screwdriver isn't sitting tight like it is for the other ones. Any idea on how to fix that?

    ben mccord -

  5. 3AbSAfsoTxUrMeTi
    3AbSAfsoTxUrMeTi
    wudY36aHJeyT6WjV

    • Separa delicatamente la copertura interna da quella bianca esterna usando il metodo appropriato.

    Essential tip: be sure to slide the metal housing backward, away from the from of the case as pictured above, rather than upward. If not, you can easily break off the teeny momentary switches on the IR blaster board!

    Mark Ross -

    “appropriate method is not descriptive like Mr. Ross’s comment. The original poster should edit the description to ensure people do in fact remove the box from the case appropriately. I would also add arrows to the picture.

    Ryan A -

    ____________⬆️

    ↖️Yes! I see it the same way!↗️

    ⬅️Arrows are always a good thing!➡️

    ↙️Can't do anything wrong with them! ↘️

    ____________⬇️

    😅😅

    profnussecke42o -

    I didn't realize that metal ribbon was connecting the case to the console and I yanked it w out realizing it was there. How o I get a replacement?

    Jerianna Mike -

  6. EFLSsRhhXsAEZnYh
    EFLSsRhhXsAEZnYh
    OjVWJsD26pdrus24

    • Per sostituire il disco rigido, gira la console a testa in giù e svita le due viti Torx T10 da 10 mm, la C3 e la C4, dal retro della Xbox One S.

    • Questo permetterà alla copertura in plastica del disco rigido di staccarsi dal resto della console.

    Some of my silver were gold screws, so just letting people know to look out for that!

    jovialkitten -

    The Torx screw circled on the left is actually C5

    Jaryn Wickman -

    I found the same. On my Xbox One S, it's C3 and C5 that hold in the hard drive caddy. C4 holds in the optical disk caddy.

    jamesr -

    Yeah, C3 and C5 on my console too.

    Jahn Roux -

    Funny thing on my console rev t t3 built feb 2018 it’s C4 and C5

    KingofRome -

    The instructions fail to mention that the top metal cover can be lifted off at this point without undoing any more screws.

    CityZ -

  7. X2IJJg3NqtsnAcbY
    X2IJJg3NqtsnAcbY
    NAHJXCj1SgvQNjOx
    3fEHBmUuTGRL3omb

    • Scollega delicatamente il disco rigido dalla scheda madre (dai due connettori in plastica).

    Do not disconnect the connector in the second image! There are tiny prongs that bend easily and if bent just a tad bit they will break off. I had first hand experience with this and I ended up breaking my Xbox because I could not put that cable back on.

    [deleted] -

    Do not remove the cable!!!! You can change while the cables are plugged. It took 2 hours trying to put mm precisely all the little pins because of the removal of the cables.

    Please update the post, I could easily end up as the Aaron, breaking the XBOX completly.

    Botond Kopacz -

    Yes, this has also happened to me the connectors had broken and the pins bent and snapped off.

    Samuel Garbutt -

  8. VxZkFMZbQAxM2dKL

    • Per rimuovere il lettore CD, svita la vite Torx T10 argento da 10 mm chiamata "C5".

    The image shows screw 'C4' witch is the correct screw. 'C5' is for the HDD.

    GoJoel -

  9. IL5gf22gGXMcJsTw

    • Tira leggermente via il lettore CD dalla scheda madre e scollega i connettori in plastica sulla scheda madre.

  10. LDNGpA5mc6kvJlfK

    • Per sostituire la scheda madre devi svitare le tre viti Torx T10 argento da 10 mm chiamate "C1", "C2" e "C6".

    • Svita le quattro viti Torx T9 nere da 8 mm chiamate "A1", "A2", "A3" e "A4".

    The Black screws are T-8 Torx, not T-9!

    Jakub Krzyskow -

    I didnt see this before, so thankfully I was able to use T9 without stripping the screws!

    Charles Jackson -

    IMPORTANT! You also need to remove the two T10 screws labeled B1 and B2 in order to remove the motherboard! I had to figure this out on my own.

    Charles Jackson -

    I hust had to remove the red ones and than i was able to lift the powersupply of the mainboard

    Dennis M -

    I had to remove B1 and B2 as well.

    Seen Bee -

  11. VYVC1GvNKhPpRiky

    • Trova il morsetto rettangolare nell'angolo opposto all'alimentatore.

    Remember to remove the black bracket by the fan!

    Martin Samuelsson -

  12. HTtOORoftr1aaQ2q

    • Prendi il morsetto con delle pinzette. Tiralo verso l'alto, lontano dalla copertura argento. Fallo ondeggiare se necessario.

    • Non preoccuparti di fare un po' di forza per rimuovere il morsetto dalla copertura argento. Il metallo si può piegare e puoi reincastrarlo come preferisci.

    • Devi svitare la piccola scheda logica vicino alla ventola prima di rimuovere la scheda madre. Penso sia dell'antenna WiFi.

    • Rimuovi la piccola scheda Mediatek etichettata D1, D2, e D3.

    What bit couldninuse tontake D1-3 screws off

    Amanda Zapata -

  15. agFplIWSUCuRiA26

    • Ora che il morsetto è stato rimosso, solleva delicatamente la scheda madre dai suoi bordi dalla copertura in metalli. La scheda madre dovrebbe uscire senza problemi.

    How do you open it?

    johnluxford07@gmail.com -

    They forget, I think, to tell that first you need to take off screw B1 and B2

    Gabriel Varela -

Conclusione

Per rimontare il tuo dispositivo, segui le istruzioni in ordine inverso.

Autore

Erik Ramazzini

Membro da: 26/04/17

2749 Reputazione

10 commenti

This guide is really missing alot between steps 13 and 14. There are two black panels that have to be removed(they’re in the teardown guide). One is on the front with with screws E1 ,E2, E3, E4. And theres another panel on the side with screws D1, D2, D3. Finally there are two more screws on the bottom that hold down the motherboard B1, and B2. Theres Also a black from in between the Fan and case that slides off too.

Nathan Stanley -

Yep, I was using this guide and realized that it is missing a few vital steps. Thank you Nathan.

Dave Miller -

If you have a multimeter could you please test the test points around the board and give me a list of a voltages?

Lilithe Lotor -

fantastic! only issues that are missing, are mentioned in the comments above. I´d like to include that most of the exterior hardcase clips are made to be HELD in place. Which is why it´s a nuisanse to remove. So, newcomers be careful with it. otherwise you´ll easily break it.

Mateus Cesar Loubach -

Son los mejores

NELSON ESTREMERA -

My xbox one s turns on, fan runs but no signal nor will not connect to controller.

I do have a faint burnt smell, any idea what could be at fault?

jaboody singh -

a 5 min job ???????? LOL

Alan Sears -

How do you remove the old heat sink from the motherboard?

Seen Bee -

How do u remove the fan?

Marco -

My father had bought me the new motherboard and in china region locked, this is not ok, you should test your reused products before selling them

L D -