Sostituzione schermatura scheda madre Huawei P9 Lite

Scritto Da: Tobias Isakeit

Commenti: 21

Sostituzione schermatura scheda madre Huawei P9 Lite

Difficoltà

Moderato

Passi

Tempo Necessario

Nessuna stima

Introduzione

Usa questa guida per rimuovere la schermatura della scheda madre con integrato il sensore impronte digitali dello Huawei P9 Lite.

Strumenti

Passo 1

Usa un plettro di apertura per far scattare le clip di fissaggio della cover posteriore, iniziando dall'angolo inferiore.
Percorri il bordo in senso antiorario e stacca una ad una le linguette di plastica.

What could you use instead of an opening pick??

Alfredo - 27/03/18

Like, could a guitar pick wor? Or anything else?

Alfredo - 27/03/18

A guitar pick will also do.

Tobias Isakeit - 27/03/18

what can still be used besides guitar pick

Tarshia Thompson - 26/11/18

I had a hard time to open the back cover by opening pick. Then I used little, really little knife at first, and I continue to opening back cover using opening pick.

Andy B - 22/02/20

Heating up aroud the finger sensor to loosen the square adhesive tape ..

Hishamchohan - 06/11/20

If you do not have any picks, You can also adapt an old credit or utility card by cutting it in to thirds. Then with some fine emery or sand paper, rub a sharp point on the one edge of the card. This will help you get access to the clips that hold the rear cover on. The one i did yesterday had quite a lot of adhesive around the edge & around the finger print sensor. Another tip with an old credit card is to cut it in to narrow strips to insert in to where you have separated the cover from the frame to stop it getting stuck to the adhesive again.

gazza667 - 06/12/20

Passo 2

C'è dell'adesivo sotto la cover posteriore che la tiene fissata alla batteria e alla piastra metallica nella parte superiore.
Fai attenzione al cavo flessibile sul lato destro.
Torci il plettro di apertura per far leva sotto la cover posteriore liberandola dall'adesivo.

Most of the adhesive is around the fingerprint cell and on the battery itself. You can slowly pull the back cover from its side but make sure not to break it. Push the mediator or a longer piece of plastic under the back cover to slowly destroy the adhesive.

Nicolas Combaret - 22/04/19

Slowly, slowly wins the day. Nicolas is right and comes off a charm. The most nerve wracking part of this longish repair.

John Nordstrom - 20/06/20

Passo 3

Una volta che la cover posteriore è libera dall'adesivo, puoi facilmente rimuoverla con la mano.

Hi! Im so sad! At the begginig of the operation i ve broken the white seal/connector that in one side is connected to the board and the other side is "glued" to the battery. Can someone help me? how can i solve this?? There is no image displayed on the screen. but there is vibration, sound, notifications... can someone help me please???

Diogo - 01/07/17

What you broke is handling the NFC, and doesn’t have anything to do with the display. You probably damaged the ribbon right below the battery, since that’s what links the display to the motherboard.

Polaris -

Oups ! L’antenne NFC était solidement collée à l’intérieur de la coque et j’ai donc déchiré sa nappe en ouvrant la coque. Heureusement, je n’utilise pas les fonctions NFC et, à part cela, tout a l’air de fonctionner normalement.

Michel Orban - 26/01/21

Passo 4

Svita le nove viti Phillips #00 che tengono in posizione la piastra metallica.
Alcune viti possono essere coperte da sticker per rilevare manomissioni. Tirali via per poter usare il cacciavite senza problemi.

Qu’est ce qu’un “indicateur d’eau”?

chevaliernoir - 21/11/19

Une petite pastille qui change de couleur au contact de l’eau. Les fabricants s’en servent pour nullifier la garantie : si ta pastille indique que de l’eau s’est infiltré, tu devra payer ta réparation.

Polaris -

Are all the screws the same size ?

Hishamchohan - 06/11/20

yes they are

Adam M -

Passo 5

Aspetta a tirare via la piastra, è collegata da un connettore e da un cavo incollato.
Usa uno spudger per disconnettere il sensore di impronte digitali dalla scheda madre.
Stacca il cavo flessibile dell'antenna NFC che aderisce alla piastra metallica.

can we just remove NFC antenna and dont want to install int back?

Mohd Danial Bin Harun - 06/08/18

Note there are two plastic tabs at the top of the shield plate. Unlock them with a mediator, the plate will come easily after that.

Nicolas Combaret - 22/04/19

Buongiorno,

va sostituita l'intera piastra metallica contenente il sensore impronte e la fotocamera, oppure il sensore é estraibile dalla piastra?

Grazie

LUIGI

GI GI - 17/08/19

Yes, it is possible to remove just the fingerprint sensor from the motherboard shield. Remove the small metal plate on the inside of the shield covering the sensor and push the fingerprint sensor through from the other side.

Tobias Isakeit - 20/08/19