WRS315SDHW Evaporator Fan Replacement

Scritto Da: nicO
  • Commenti: 0
WRS315SDHW Evaporator Fan Replacement

Difficoltà

Moderate

Passi

15

Tempo Necessario

30 - 45 minuti

Introduzione

Use this guide to replace the evaporator fan in your Whirlpool WRS315SDHW Refrigerator.

The evaporator fan draws air over the cooling coils and circulates this air within the fridge and freezer compartments. If your refrigerator is not cooling but your freezer works, then your evaporator fan might be broken.

Note: Some photos show the doors removed for clarity purposes. Removing them is not required and will not change the procedure.

  1. GAB31IUS1UwNdE6E

    • Before you begin your repair, perform the following:

    • Turn off your main water supply

    • Unplug your device

  2. uZnovp3POltPPcNl
    uZnovp3POltPPcNl
    EEmEHtDyinkLLTC6
    NpS45AODrJVIyexU

    • Depending on your repair, open one or both doors.

  3. hkAwPUpRPNIPxRGV
    hkAwPUpRPNIPxRGV
    L4ikmh2NQXFogcpt

    • Remove the drawers and shelves from the freezer section.

  4. PYjtoq32XfA1ZLfx
    PYjtoq32XfA1ZLfx
    vH1YKrFTgcoJSpj3

    • Remove the screw(s) securing the evaporator cover.

  5. EHSDsDxpXbXtjjSW
    EHSDsDxpXbXtjjSW
    Wf2DVMGatSZhfSRa
    2oHDgU6UMdQXqWmO

    • Lift the bottom of the evaporator cover up and over its lip in the chassis.

    • Pull the cover toward yourself to release its top clips.

  6. YeaE3oqkUY5iSaJh
    YeaE3oqkUY5iSaJh
    TdRPKBwJHWNGAEoK
    41LUePiTbxqKJb1K

    • Continue pulling the evaporator cover towards yourself to unclip its metal prongs from the chassis.

    • Remove the evaporator cover.

  7. IiR22JP2G5I1UDln
    IiR22JP2G5I1UDln
    J4IMwZ6Jg212qmEA

    • Use needle nose pliers, or your fingers, to disconnect the grounding wire attached to the evaporator fan.

  8. LWjkpnMUatQDoToa
    LWjkpnMUatQDoToa
    5MIOLZURtMgQxYvu
    LDP1AFXgGbHrp6yG

    • Disconnect the connector attached to the evaporator fan.

  9. SCl1h6jlHbIu1sh2

    • Use a 1/4 inch socket wrench to remove the two 13 mm-long screws securing the evaporator fan.

  10. oI2pmGCxk6hYhvWD
    oI2pmGCxk6hYhvWD
    quQmTuWOlIuAgwUy
    IZdfcNV41pZJ1KKi

    • Slide the foam buffer downward to release it from its lip in the chassis.

    • Remove the foam buffer.

    • Repeat this procedure for the second foam buffer.

  11. ZqiwaIy1BaAPrQVv
    ZqiwaIy1BaAPrQVv
    PCsBSbT5FAgOqGMd
    W2D2Tqgi2MkgKbUQ

    • Pull the evaporator fan housing up and outward from the chassis to remove it.

  12. MbIPWKZjK4NmQsGy
    MbIPWKZjK4NmQsGy
    QLE5clwjOVfGXYeB

    • Pull the evaporator fan straight off its motor to remove it.

    • This may require some significant force.

  13. iRKpFkls3ttRwToo
    iRKpFkls3ttRwToo
    VW5GulMj5pFRNiGx
    VFoHSNtV2mf6u4lm

    • Use your fingers to pry up and release the motor bracket clips from the housing.

  14. QIuw2BxqK221o65F
    QIuw2BxqK221o65F
    XyKKSFlJWeATMtmq

    • Remove the motor bracket.

  15. PfrU3PlUtpfdBaDx
    PfrU3PlUtpfdBaDx
    cTbIIGxPaRVR5pie
    HOIoNLXeovAGF1kW

    • Pull the motor straight out of its housing to remove it.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Ask our Answers community for help.

Autore

nicO

Membro da: 14/04/15

15885 Reputazione

0 commenti