Xelio P1001A-BK DC Power Socket Replacement

Scritto Da: Michael Case
  • Commenti: 0
Xelio P1001A-BK DC Power Socket Replacement

Difficoltà

Moderate

Passi

15

Tempo Necessario

Nessuna stima

Introduzione

If the power connector on the Xelio P1001A-BK tablet is damaged, it can be de-soldered from the motherboard and replaced with a new part. This is a 2.5mm x .7mm power plug which should be readily available from most electronic parts stores. The repair should take about one hour for the intermediate do-it-yourselfer.

Since the motherboard will be exposed, care should be taken to prevent short circuiting the power leads from the battery or allowing static electricity to damage the motherboard. An antistatic mat should be used if available.

Be patient and go slow with this repair as several small parts will be removed and the could be easily damaged or lost. A magnetic mat or parts tray is recommended to keep small parts together.

  1. BukuvfvWIaRrWqB5
    BukuvfvWIaRrWqB5
    RsjBNRluDBa5NGWD

    • Remove the two 3 mm retaining screws from the side of the tablet with a Phillips #0 screwdriver.

  2. 4X1ZsMMgt3kRgGSL
    4X1ZsMMgt3kRgGSL
    UoJFKdSHK1kijLtb

    • Insert the plastic opening tool in between the shelf halves and lift the top shelf half to detach the securing tabs.

    • There are four securing tabs located on each long side.

    • Before fully separating the shell halves, observe if the speakers are separated from the shell half. If they are still in their sockets, gently pry them loose with the plastic opening tool.

  3. ntRpptOnpTbjYrNL

    • Remove the micro-SD card from the card slot if a card is in the slot

  4. VT3mJVsJLvga1nNl
    VT3mJVsJLvga1nNl
    PDFOJYeppjcFI3Nj

    • Remove the motherboard to screen ribbon cable

    • Pry the ribbon cable retaining tab loose with plastic opening tool.

    • Slide the ribbon cable out from the connector.

  5. 5dsdGGUWk6FvTUuQ

    • Remove the camera from its socket. Do not remove the camera ribbon cable.

  6. RrMQQYf2IcJSyelZ
    RrMQQYf2IcJSyelZ
    tyleSSsAAFdtL3sF

    • Remove the two motherboard retaining clip screws with a No. 0 Philips head screwdriver

    • Remove the retaining clip from the board.

  7. MXUv2NIielCTIISc

    • With the No. 0 Phillips head screwdriver, remove the two screw that hold the function and volume control switch assembly to the tablet.

  8. OLcBUJyoRWFh4LiM

    • Remove the two screws that secure the micro-SD card reader to the tablet frame

  9. qjElXEqGFsWNCjEG
    qjElXEqGFsWNCjEG
    1xexEyauM1nQf2rT

    • Remove the three screws that secure the motherboard to the tablet frame

  10. 3hROR1XmZ3JR5HIX
    3hROR1XmZ3JR5HIX
    ImlIH1OExYjmpvLx

    • Gently lift the motherboard free from the tablet frame and turn it over to expose the opposite side. This will expose the power socket solder pins.

    • Be cautious when turning the board over as another ribbon cable, the speaker wires, battery wires, and Wi-Fi antenna wire as still connected to the motherboard.

  11. 5HtKbjSjCXHMtCOY

    • De-solder each of the solder points.

  12. d1dHIjJXcR2EbQJG

    • Remove the damaged power socket.

    • Use a needle nose pliers or pair of tweezers to hold the power socket as it is a small part and may be difficult to hold.

    • Be careful to avoid touching the solder pins as they may still be hot

  13. aubK4XSbOiBXu1DB

    • Place the new part on the board

    • Solder the new part into place

  14. ELwseSCRDfTSrUEa

    • Place the motherboard back into its proper position but do not reinstall the securing screws yet.

  15. yTbnjtnF2pCGlYTv

    • Plug the tablet power supply into the power socket

    • Using a volt-ohm meter, touch the meter probes to the battery wire points on the motherboard to ensure voltage is getting to the battery.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Michael Case

Membro da: 11/03/15

110 Reputazione

0 commenti