Battery Disconnect

Scritto Da: Spencer Day
  • Commenti: 0
Battery Disconnect

Difficoltà

Moderate

Passi

8

Tempo Necessario

Nessuna stima

Introduzione

Use this guide to disconnect the battery in your Razer Blade 15 Advanced Model (Early 2020) laptop. The battery should be disconnected before all major repairs.

  1. U3WCBShbaLvURkIn
    U3WCBShbaLvURkIn
    DLKeF3nRAqw6JZHV

    • Allow your laptop's battery to drain below 25% before starting this repair—a charged battery may catch fire if damaged.

    • Unplug all cables, fully shut down your laptop, and close the lid.

  2. mwpZH3qBEQhGfMsZ
    mwpZH3qBEQhGfMsZ
    eZC5IteTOvPV2SRH

    • Use a T5 Torx driver to remove the ten 3.8 mm‑long screws securing the back cover.

  3. UyswDlrMoOuPxypO
    UyswDlrMoOuPxypO
    ZCQLS6SmYFD16roT
    AKZCEEwppCqshwfw

    • Depending on the age and condition of your laptop, the back cover may come off sooner than this guide instructs. If it feels loose, remove it at any time.

    • Apply a suction handle to the middle of the back cover's right edge, between the lower rubber foot and the middle screws.

    • Pull up on the suction handle to create a small gap between the back cover and the frame.

    • Insert an opening pick into the gap.

  4. 5ZeHhQqyGyPNtQ2Z
    5ZeHhQqyGyPNtQ2Z
    65pDl33yTCvLjvtV
    6GNJkCfOsbUZWFQE

    • Angle your opening pick upward, away from the frame. Keep it angled upward as long as it's between the back cover and the frame.

  5. aoYEQ1ZuOohURDBV
    aoYEQ1ZuOohURDBV
    3wZjhrAbjWVHpYDE
    QaiFOX5uygSIVlEo

    • Slide your opening pick around the bottom right corner of the back cover to free it from the frame.

  6. aoJKrYRFNEwNCsgQ
    aoJKrYRFNEwNCsgQ
    WU5LeqALfrufkyDR
    1ig13qvemkhwD3TF

    • Slide your opening pick along the front edge and around the front left corner of the back cover to free it from the frame completely.

  7. BqSgYh6T41JWJKVM
    BqSgYh6T41JWJKVM
    YdTVUNPk3FW4GaDO
    CXegRG4dUtw3Cpol

    • Remove the back cover.

    • Lay the back cover down on its rubber feet to avoid damaging the thermal pads.

  8. 2vxabbeLFF4TYtlM
    2vxabbeLFF4TYtlM
    IKvPRa4pTtoKIJHM
    p1RIxJKZIoG6spRk

    • Insert the point of a spudger under the middle of the battery connector's long edge.

    • Lift and disconnect the battery press connector from its socket on the motherboard.

    • This will require some force. Don't pry against any resistors or chips.

    • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don't press down in the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Spencer Day

Membro da: 14/09/22

48838 Reputazione

0 commenti