Meta Quest 2 Eyepiece Trim Replacement

Scritto Da: Arthur Shi
  • Commenti: 0
Meta Quest 2 Eyepiece Trim Replacement

Difficoltà

Moderate

Passi

18

Tempo Necessario

10 - 30 minuti

Introduzione

This guide shows how to remove and replace the eyepiece trim for your Meta Quest 2.

The eyepiece trim is a plastic piece which the facial interface clips onto. It also contains the face sensor.

  1. SqbHLQOA2SemeF4D

    • Hold the power button for three seconds to fully turn off your headset.

    • You'll hear a power down chime, and the LED next to the power button will turn off.

  2. B31djmGYZZHCBoti
    B31djmGYZZHCBoti
    OEu2hrgBLV4wSLKR

    • Grasp and pull on the nose section of the facial interface to unclip it from the headset.

  3. Be2J2NaNLeqZuRhi
    Be2J2NaNLeqZuRhi
    BFoGtcvupgIvCQIK

    • Grasp and pull on the top section of the facial interface to unclip it from the headset.

  4. uLFjxFFQlhXdWAtB

    • Remove the facial interface.

    • During reassembly, align the facial interface to the headset and use your fingers to press along the perimeter to clip it back in.

  5. URh1oymFaf6RLYSM
    URh1oymFaf6RLYSM
    yHfWoon1NiqXGyYB
    CDnYbnLkUxyibGsY

    • Use your fingers to grasp the right strap near the headset.

    • Peel the right strap away from the headset arm to unclip it.

  6. 4nENMVhqOjgOunbA
    4nENMVhqOjgOunbA
    Moo6ThGGPZGnMGZV

    • Repeat the procedure to peel the left strap away from the arm to unclip it.

  7. hSyfJboRQGTssgOk
    hSyfJboRQGTssgOk
    t5EGhNgdrvxuoPHu

    • Separate the hook and loop strip on the top strap.

  8. wquuIQnnECAaTkt2
    wquuIQnnECAaTkt2
    JVJruOK5jI2NowDF

    • Unthread the top strap from its bracket.

    • Remove the head strap.

  9. yPeQSMKFUNr1DPW5
    yPeQSMKFUNr1DPW5
    wRjMBK6TWEpLYbBA

    • Use a Torx T2 driver to remove the six 3.5 mm‑long screws securing the eyepiece trim.

  10. awTJYMHOLskpVy4a
    awTJYMHOLskpVy4a
    KWMNHLbd5KelgGYP

    • Insert an opening pick into the seam between the eyepiece trim and white outer shell, near the nose cutout.

  11. ryWGlBHZ6TRrA2q3
    ryWGlBHZ6TRrA2q3
    AZiweYguFJHZQQJu
    MaqaHyaOdJr2NIML

    • Slide the opening pick to the right along the seam to release the clips securing the eyepiece trim.

    • Pry with the opening pick to release the clips securing the right side of the eyepiece trim.

    • Leave the opening pick in the seam to prevent the clips from reengaging.

  12. Sa24OOHFX6N4vDmB
    Sa24OOHFX6N4vDmB
    3iNTLEdaGtMhjiyk
    pu63GssAMaSOmugP

    • Repeat the prying procedure along the left edge to release the clips securing the eyepiece trim.

    • During reassembly, press your fingers along the perimeter of the eyepiece trim to clip it back in place.

  13. 6UjuCJF2TSnIAy4n
    6UjuCJF2TSnIAy4n
    IKRAfAuj4VCBFKUD
    oW4opLiLOo6DACSH

    • Don’t try to fully remove the eyepiece trim in this step. It’s still connected to the headset by a short cable.

    • Lift the eyepiece trim slightly and tilt it towards the top edge of the headset.

    • Set the trim down on your work surface, making sure not to strain the cable.

  14. IDPgUcSVOPIEsjVV
    IDPgUcSVOPIEsjVV
    5u5lQh6PJ2chJBwb
    lj1QMH44RFNZEuRQ

    • Use the point of a spudger to flip open the black lock tab on the ZIF connector securing the face sensor cable.

  15. HJpDCNb5JfYwxOIJ
    HJpDCNb5JfYwxOIJ
    jZnsVTqBDoUbP5lG

    • Use tweezers to pull the face sensor cable out of the ZIF connector.

  16. LMhTeOsbLDb1XMV5

    • Remove the eyepiece trim.

  17. eeARhGrBQQX4Svh6
    eeARhGrBQQX4Svh6
    fVmHwAqUICN2xLEh

    • During reassembly:

    • Make sure the lens spacing matches the spacing indicator. This allows the indicator peg to sit correctly in its notch.

    • If the lens spacing doesn't match the indicator, manually adjust the lens with your fingers.

  18. ieFjqZM1WWktjJba
    ieFjqZM1WWktjJba
    XPwf1y2hpXquo2Y6
    6ASSdjFCu4I2QxSu

    • During reassembly, the face sensor cable can be tricky to connect. Follow these tips to connect the cable:

    • Thread your fingers through the eyepiece trim’s eyeholes and grasp the edges of the sensor cable.

    • Slide the sensor cable into the socket until the first set of tabs rests in the socket. This should flip the lock tab down partially.

    • Use a spudger to press the lock tab down towards the cable to lock it in place.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Autore

Arthur Shi

Membro da: 03/01/18

248264 Reputazione

0 commenti