Introduzione
Grazie a Dio, non è più necessario rimuovere la scheda logica per sostituire la batteria in questi nuovi MacBook Pro!
Segui queste istruzioni per sostituire la batteria incollata del tuo MacBook Pro con l'aiuto di un kit iFixit dotato di antiadesivo liquido. L'antiadesivo dissolverà la colla che fissa la vecchia batteria, permettendoti di rimuoverla più facilmente.
L'antiadesivo iFixit è infiammabile. Esegui questa procedura in un'area ben ventilata. Non fumare o lavorare vicino a una fiamma libera.
Per minimizzare il rischio di danneggiamenti, accendi il tuo MacBook e consenti alla batteria di scaricarsi completamente prima di iniziare questa procedura. Una batteria al litio-ioni carica può creare un incendio pericoloso e incontrollabile se viene forata accidentalmente. Se la tua batteria è gonfia, prendi adeguate precauzioni.
Nota: il solvente utilizzato per sciogliere la colla della batteria può danneggiare alcuni tipi di plastica. Segui tutte le istruzioni e stai attento quando applichi l'antiadesivo.
Strumenti
Ricambi
-
-
Accendi il tuo Mac e apri Terminal.
-
Copia e incolla il seguente comando (oppure digitalo esattamente) in Terminal:
-
sudo nvram AutoBoot=%00
-
Premi [return]. Se richiesta, inserisci la tua password di amministratore e premi di nuovo [return]. Nota: il tuo tasto return può essere etichettato anche come ⏎ o "enter."
-
sudo nvram AutoBoot=%03
-
-
-
Usa un cacciavite pentalobe P5 per rimuovere le sei viti fissaggio della cover inferiore.
-
Due viti da 6,2 mm
-
Quattro viti da 3,4 mm
-
-
-
Applica una ventosa alla cover inferiore in centro vicino alla parte anteriore del MacBook Pro.
-
Tira la ventosa per creare una sottile fessura tra la cover inferiore e la scocca.
-
-
-
Inserisci l'angolo di un plettro di apertura nello spazio tra la cover inferiore della scocca.
-
Fai scorrere il plettro di apertura attorno all'angolo più vicino, fino a metà strada del lato del case.
-
-
-
Ripeti il passo precedente sul lato opposto, facendo scorrere il plettro di apertura sotto la cover inferiore e lungo il lato per poter sganciare la seconda clip.
-
-
-
Inserisci il plettro di apertura di nuovo sotto il bordo anteriore del case inferiore, vicino a uno dei fori delle viti più centrali.
-
Applica una decisa torsione al plettro per liberare la terza clip di fissaggio.
-
Ripeti questa procedura vicino all'altro dei fori più centrali delle viti, liberando così la quarta clip.
-
-
-
Tira la cover inferiore con decisione verso la parte anteriore del MacBook (allontanandolo quindi dalla zona delle cerniere) per separare l'ultima clip di fissaggio del case.
-
Tira prima da un angolo e poi dall'altro
-
-
-
Rimuovi la cover inferiore.
-
Disponilo in posizione e allinea le clip scorrevoli vicino alla cerniera dello schermo. Premi la cover verso il basso e quindi falla scorrere verso la cerniera. Dovrebbe smettere di scorrere una volta che le clip si sono agganciate.
-
Quando le clip scorrevoli sono completamente agganciate e il case inferiore appare allineato correttamente, premi la cover con fermezza per agganciare le quattro clip sottostanti. Dovresti percepire e udire le clip che scattano in posizione di bloccaggio.
-
-
-
Stacca con cautela l'ampio pezzo di nastro adesivo che copre il connettore della batteria, sul bordo della scheda logica più vicino alla batteria stessa.
-
Rimuovi il nastro adesivo.
-
-
-
Stacca delicatamente il piccolo pezzo di nastro adesivo che copre il connettore del cavo dati della scheda batteria.
-
-
-
Usa la punta di spudger per sbloccare, sollevandola, la piccola aletta di bloccaggio nera che trattiene il cavo nel suo connettore.
-
-
-
Scollega il cavo dati della scheda batteria facendolo scorrere fuori dal suo zoccolo.
-
Fai scorrere il cavo parallelamente alla scheda logica, nella direzione del cavo stesso.
-
-
-
Usa un cacciavite Torx T5 per rimuovere la vite a testa larga da 3,7 mm che tiene bloccato il connettore dell'alimentazione della batteria.
-
-
-
Usa uno spudger per sollevare con delicatezza il connettore dell'alimentazione della batteria, scollegando quindi la batteria stessa.
-
Solleva il connettore quanto basta perché resti separato dal suo zoccolo. Se dovesse fare contatto accidentalmente nel corso della tua riparazione, il tuo MacBook Pro si potrebbe danneggiare.
-
-
-
Utilizza un cacciavite Torx T3 per rimuovere le due viti da 1,8 mm che fissano il supporto del connettore del cavo del trackpad.
-
-
-
Utilizza uno spudger per disconnettere il cavo a nastro del trackpad, sollevando delicatamente il suo connettore direttamente dalla scheda logica.
-
-
-
Prepara un iOpener e posizionalo sulla parte superiore del cavo a nastro del trackpad per circa un minuto, in modo da ammorbidire l'adesivo che tiene saldamente il cavo a nastro del trackpad nella parte superiore della batteria.
-
Se non hai un iOpener, utilizza un asciugacapelli per scaldare il cavo. Il cavo dovrebbe essere caldo, ma non troppo caldo al tatto. Fai attenzione a non surriscaldare la batteria.
-
-
-
Utilizza un cacciavite Torx T5 per rimuovere le dieci viti che fissano l'assemblaggio del trackpad:
-
Due viti da 4,3 mm
-
Otto viti da 5,8 mm
-
-
-
Apri leggermente lo schermo per accedere al trackpad.
-
Fai passare con attenzione il cavo a nastro del trackpad attraverso il foro nel telaio del MacBook Pro.
-
-
-
Rimuovi l'assemblaggio del trackpad.
-
Assicurati di non perdere i sei piccoli distanziali (due circolari e quattro rettangolari) posizionati sulla parte inferiore del trackpad.
-
-
-
Usa un cacciavite Torx T5 per rimuovere dalla scheda della batteria le due viti lunghe 3,2 mm.
-
-
-
Per proteggere il display, inserisci un foglio di alluminio tra lo schermo e la tastiera e lascialo in questa posizione mentre lavori.
-
Puoi anche disporre un foglio di carta da cucina direttamente al di sotto dell'area del trackpad. In alternativa, puoi anche disporre una salvietta assorbente direttamente al di sotto della zona del trackpad per assorbire un'eventuale colatura di antiadesivo.
-
-
-
Taglia un pezzetto di nastro da pacchi o da mascheratura e infila uno dei bordi tra la batteria e l'altoparlante del lato sinistro.
-
-
-
Premi lungo tutto il bordo del nastro con lo spudger per far aderire bene alla scocca di alluminio del MacBook Pro, sigillando così l'altoparlante rispetto alla batteria.
-
Ripiega l'altro bordo del nastro e fallo aderire leggermente all'altoparlante in modo che non dia fastidio.
-
-
-
Ripeti i due passi precedenti sul lato opposto per sigillare l'altro altoparlante rispetto alla batteria
-
-
-
Per controllare il flusso dell'antiadesivo e dirigerlo lontano dall'altoparlante, solleva di qualche centimetro il bordo destro del tuo MacBook Pro usando un libro o un pezzo di espanso.
-
-
-
Ora che il tuo MacBook Pro è stato preparato per l'intervento, è ora di preparare anche te.
-
Indossa occhiali protettivi quando maneggi e applichi l'antiadesivo (gli occhiali protettivi sono inclusi nel tuo kit).
-
Non indossare lenti a contatto senza gli occhiali protettivi.
-
Anche i guanti protettivi sono inclusi nel tuo kit. Se ti preoccupa un'eventuale irritazione alla pelle, mettiti subito i guanti.
-
-
-
Tira via il cappuccio nero di gomma dalla tua bottiglia di antiadesivo.
-
Usa delle forbici per tagliare la punta ancora sigillata dell'applicatore.
-
Effettuare il taglio vicino all'estremità più stretta ti darà un controllo migliore perché potrai applicare l'antiadesivo in piccole quantità.
-
-
-
Applica poche gocce di antiadesivo sotto la cella della batteria disposta all'estrema destra.
-
Aspetta un paio di minuti prima di procedere con il passo successivo, per dare tempo all'antiadesivo di penetrare e ammorbidire la colla.
-
-
-
Dopo un paio di minuti, inserisci un angolo di una scheda di plastica sotto la cella della batteria più a destra, iniziando dal bordo anteriore.
-
Fai oscillare la scheda da un lato all'altro e falla scorrere completamente sotto la cella della batteria.
-
Solleva la cella per separare completamente l'adesivo, ma non cercare di rimuovere del tutto la cella già ora.
-
Lascia temporaneamente la scheda di plastica sotto la cella della batteria per evitare che la colla possa riattaccarsi.
-
-
-
Se incontri delle difficoltà a infilare la scheda sotto una qualsiasi delle celle della batteria, cerca di far passare un un pezzo di filo interdentale o un cavetto al di sotto della cella della batteria. Tiralo da un lato all'altro con un movimento alternato per staccare l'adesivo.
-
-
-
Ripeti gli ultimi passi per staccare la cella della batteria all'estrema sinistra.
-
Inizia sollevando il lato sinistro del MacBook Pro per indirizzare il flusso di antiadesivo lontano dall'altoparlante.
-
-
-
Applica poche gocce di antiadesivo sotto la cella della batteria più a sinistra e attendi circa due minuti per lasciare al solvente il tempo di agire.
-
-
-
Fai scorrere l'angolo di una scheda di plastica sotto la cella della batteria più a sinistra e stacca con delicatezza l'adesivo che blocca la cella stessa..
-
Lascia temporaneamente la scheda di plastica sotto la cella della batteria per evitare che la colla possa riattaccarsi.
-
-
-
Ora, alza il bordo posteriore del MacBook Pro per indirizzare il flusso di antiadesivo lontano dalla zona della tastiera e della scheda logica.
-
-
-
Applica poche gocce di antiadesivo sotto ciascuna delle tre celle rimaste della batteria.
-
Stai attento alle colature e, se necessario, applica dell'altro antiadesivo nei passi seguenti.
-
Aspetta un paio di minuti prima di continuare.
-
-
-
Fai scorrere una scheda di plastica interamente sotto la cella della batteria all'estrema sinistra - quella che hai già staccato nei passi precedenti - e poi inseriscila con delicatezza tra la cella di sinistra rimasta e la scocca di alluminio.
-
-
-
Usa la tua scheda di plastica per staccare completamente la cella della batteria rimasta sul lato sinistro.
-
Lascia temporaneamente la scheda di plastica sotto le celle tra per impedire che la colla sottostante possa riattaccarsi.
-
-
-
Ripeti i due passi precedenti per staccare la cella della batteria rimasta incollata a destra.
-
-
-
Fai scorrere l'angolo di una delle tue schede di plastica sotto il bordo superiore di una delle due celle e quindi inizia a lavorare anche sotto l'altra cella.
-
Muovi la scheda da un lato all'altro e fallo scorrere sotto le celle della batteria per staccare completamente l'adesivo che le tiene in posizione.
-
-
-
Rimuovi la batteria.
-
Stacca i pezzi più grossi di adesivo rimasto con delle pinzette o le dita protette da guanti.
-
Raschia tutti i piccoli pezzi rimasti di adesivo con uno strumento di plastica e pulisci l'area interessata con antiadesivo oppure alcol isopropilico. Sfrega in una sola direzione (non avanti e indietro) finché lo chassis sarà pulito e pronto ad accogliere una nuova batteria.
-
Una volta terminato, rimuovi il nastro protettivo dagli altoparlanti con delicatezza.
-
-
-
Stai attento al cavo dati della batteria e accertati che non rimanga pinzato o intrappolato sotto la scheda della batteria.
-
Se la tua batteria è dotata di adesivo preinstallato sul retro, rovesciala e stacca cura il foglio protettivo per esporre la colla. Se la tua batteria non è già dotata di adesivo, applica un nastro biadesivo sottile come il Tesa 61395 per attaccare la batteria.
-
Posiziona con cura la batteria e installala al suo posto.
-
Premi con decisione ciascuna cella tenendola premuta per 5-10 secondi per fissarla al case inferiore.
-
Confronta la tua parte di ricambio con quella originale: potrebbe essere necessario il trasferimento di alcuni componenti o la rimozione di protezioni adesive dalla nuova parte prima di installarla.
Per riassemblare il tuo dispositivo, segui i passi descritti in ordine inverso.
Porta i tuoi rifiuti elettronici a un riciclatore certificato R2 o e-Stewards.
La riparazione non è andata come previsto? Prova delle soluzioni di base ai problemi dopo una riparazione, oppure rivolgiti alla nostra comunità Risposte per trovare aiuto nella risoluzione dei problemi.
15 commenti
When remounting, putting back the trackpad in a nicely centered position can become a lengthy exercise of patience.
I haven’t find guides or tricks to help; the best I came up with was to
* put back just two corner screws, without tightening them, that is enough to keep it in place and not lose the washers
* flip back your macbook keyboard up
* center the trackpad and fix it in place with adhesive tape
* flip it back belly-up, tighten the two corner screws and add the remaining six.
Thanks; everything went well, except at the end I realized that I somehow damaged the battery connector from step 12/13. What is the part number, please?
The replacement went very smoothly, and when I re-assembled the laptop, the spacebar and command keys seemed tight. Any thoughts about how that might happen?
JNM -
Is this step necessary? I can’t perform this step as I am attempting to repair water damage and need to remove logic board & most likely replace the battery.
Macrepair SF -
@mac_medic You definitely don’t want the power coming on while the board is wet. In your case, I think powering on the machine to disable Auto Boot would do more damage than it prevents. I agree, skip this step and be prepared to disconnect the battery quickly if the laptop automatically powers on. Good luck!
Jeff Suovanen -
Thats right! You don't want power running while working on your logic board.
Dan -
This did not work when running High Sierra.
Kyle B -
Tried this on a 2018 MBP 13” Touchbar (there’s no iFixit guide for this model yet). Need to replace a broken screen.
Luckily I managed to connect to an external screen (Cmd-Down Brightness to switch displays) and enter above command. Seems to work, but there’s another problem with this model - it powers up as soon as any key is pressed……. ffs <gnashes teeth>
Cool_Breeze -
I unscrew the battery first and wrap electrical tape over the logic board battery connector before attempting any repairs to the board. Haven’t had any problems yet and I’ve worked on about 10 of these models already. Also when you open the bottom case use a suction cup at the bottom and pull up then run a plastic spudger along the edges to disconnect the clips. Also only use a plastic spudger on the board. Saw a youtube video from a repair shop and he did not disconnect the power and used all metal tools during the entire process of removing the board. His last step was to disconnect the battery terminal.
Brian -
Is this step necessary if my mac can turn on? Battery fully dead(
Nursat b -
BEFORE YOU START: The included torx head stripped off before I was done (and you might need an additional T4) so stop now and go buy a good one. Also they fail to warn you above to get some blue threadlocker ahead of time.
Jason Sherron -
This command did not work for me and I read that sometime in later 2020 Apple stopped this command from working…any ideas on a work around?
Patrick Machacek -
Not able to do that with damaged screen
richardjgreen -
If you have a damaged screen you can still use a converter from thunderbolt (USB 3) to HDMI and plug your Macbook Pro to your TV as monitor display. Just make sure to chose the right Source (HDMI IN) in your TV. I did it and to make it work I unplug and plug again in my Macbook and so I could disable the Auto boot
Roberto Sanchez Bustos -
Hi. This does not work on 2018 13” MacBook Pro with Touch Bar. I did exactly this to disable auto boot. But when I check by using nvram -p it says: auto-boot true. Am I doing something incorrectly? I did everything step by step. Copied and pasted the sudo command, pressed enter and then entered my password. I have Big Sur 11.1 installed. Is there any other way since I need to replace the screen. Thank you. Adrian
Adrian Vizik -
Hi everyone. This is also a little pointless if you can’t see anything on the screen, and you don’t have a display adapter to USB C to display it. I agree with Brian about removing the back and disconnecting the battery cable before you even think about opening the lid of the MacBook. Applying the insulation tape is also a handy little tip that just makes sure there is no way to discharge from either the board or battery.
Roberto Enrieu -
running `nvram -p | grep 'AutoBoot'` in terminal verifies that it was accepted
result: `AutoBoot %00`
Marek Polák -
Running Big Sur 11.6.7 on a 2019 16" MBP, it's "auto-boot". So it's:
nvram -p | grep 'auto-boot'
to display the current state, the default istrue
- and then to change it,sudo nvram auto-boot=false
which turns it off.Ed Mechem -
This step is completely unnecessary if you follow the guide to disconnect the battery properly. Just put some tape between the battery and logic board connection to prevent it from accidentally touching and therefore powering on the laptop.
Grant Ormsby -
It took me a few tries to make this command work, as I was able to copy and paste the command into Terminal, but could not type in my laptop’s password. I finally typed my password into a text document, copied it (command C), and then pasted it into Terminal and it worked.
tommy404 -
I didn’t do this. Mine never auto-booted before I replaced the battery. Now it does.
hatuxka -
BEFORE YOU DO ANYTHING - CHECK THE BATTERY!
I-fixit sent me a bad battery, which I didn’t realize until it was already install. They sent me a new one, but I wasted hours uninstalling and reinstalled.
Get a volt meter and measure the voltage on the output of the battery pack. If it reads 0 V, SEND IT BACK. It should read over 2 V.
bcardanha -
I've just received my replacement battery and it reads 0,042V between the two main connectors. Do you think it's dead?
peter sussex -
When I did this from Terminal.app within Recovery Mode, the “sudo” was not recognized but I could invoke it without the sudo part. It seems to have been accepted when looking at “nvram -p”
johann beda -
When in Recovery Mode, you already have superuser powers. So you don't need to prefix commands with the sudo command to invoke them with root privileges; you already have them. Do a
pwd
(print working directory) after opening Terminal in Recovery Mode, and you'll see that you're in the root user's directory.Ed Mechem -
I received the battery kit for my 2018 MacBook Pro and as per the above comment from bcardanha - Oct 12, 2021, I checked the voltage on the pads marked + and - . It was zero volts so I panicked a bit.
I sent a message on the iFixiT Facebook page and I got no reply. I finally found the customer service email for Ifixit Europe and sent them an email voicing my concern as I was not keen to work for couple of hours just to discover that the battery is faulty. I had an almost instant reply on the email (kudos to them) and they adviced me to go ahead and install the new battery as the voltage measured when battery is not connected is not relevant.
I took a leap of faith and after two hours… the new battery showed 50% charge and everything seems to be working just fine. I am happy it worked.
Mircea Comanici -
After removing the old battery and installing the new battery I powered up the MBP before screwing the bottom on. I discovered the my keyboard would not function. It took a few hours of investigation and frustration that I discovered the track pad power ribbon had become partially dislodged from the trackpad. I was able to see that this through the little machined slot where the battery sat. I had to remove the trackpad to reinsert the power ribbon back into the connector in the trackpad. after reassembling and reinstalling the battery etc the keyboard worked. Just food for thought if your run into the keyboard issue.
Ed Mease -
This should be the default. IMO I tell you to power on - not the lid.
G Sena -
Est ce que cela fonctionne sur un macbook pro 2017 sans touchbar ?
maël muzelet -
Bonjour Maël, oui, ce tutoriel concerne "les MacBook Pro 2016 (et plus récents) et les MacBook Retina 12" 2017 (et plus récents)"
Claire Miesch -
Excellent instructions. I was able to follow and install the new screen. I recommend that you get a good set of tools before you begin. I started with an inexpensive repair kit bought online. The Penta and torx bits failed. I bought an IFIXIT kit with quality bits and I was able to do everything I needed.
Tom Markham -
If you're not running an admin account the sudo command won't work (which honestly, you should not be running admin). Rather than logging in to your admin amount via the OS, in the terminal type "login [admin username]," then the password and you'll be able to do the sudo command as described above. Once you're complete, type "logout [admin username]" and you'll be good to go. Obviously replace [admin username] with whatever the account name for your admin user is.
arichard2401 -
For those unable to complete this step because the screen is too damaged I recommend leaving your macbook on until the battery dies.
Nicholas R Licato -
Just replaced my 2018 15" MBP battery. Running Sonoma.
I found no way to disable AutoBoot (The status can be checked in the Power section of system report).
Anyway, i left my battery completely drain before opening the MBP, and had no issues during the process.
Cédric Bontems -
After sending this command in terminal when I checked what happens if I now open the lid, instead the screen lit slightly up (still black) then a battery symbol showing the charging state showed up.
Now, after replacement of the battery, this is all I get to see.
No reset of NVRAM nor PRAM helped.
Currently the new battery charges (58% atm) and it feels like it‘s mocking me.
webrockers -
I suspected the keyboard or TouchID sensor wouldn’t work, so I went on and checked every connector.
I missed connecting the left TouchID sensor from step 31.
webrockers -