Steam Deck OLED Heat Sink Replacement

Scritto Da: Clay Eickemeyer
  • Commenti: 3
Steam Deck OLED Heat Sink Replacement

Difficoltà

Moderate

Passi

16

Tempo Necessario

45 minuti - 1 ora

Introduzione

Use this guide to replace the heat sink in your Steam Deck OLED.

Remember to follow general electrostatic discharge (ESD) safety procedures while repairing your device.

You'll need replacement thermal paste to complete this repair.

  1. wg1CPbiBgYbiTVlf
    wg1CPbiBgYbiTVlf
    nJjXUM3KksnJHIgN
    mLdVpQ6WWvINGWuE

    • Turn on your Steam Deck and allow the battery to discharge below 25% before starting your repairs, as a charged lithium-ion polymer battery can be dangerous if accidentally punctured.

    • As an extra precaution, Valve recommends putting your Steam Deck into battery storage mode within the BIOS before starting any internal repairs. Read how to do that here.

    • Power down your Steam Deck and unplug any cables.

    • If you have a microSD card installed, make sure to remove it before opening the Steam Deck. If you attempt to remove the back cover with it still installed, it could snap right in half.

    • During your repair, it can be helpful at times to lay the Steam Deck face-down in its case to protect the thumbsticks and prevent wobble.

  2. CU2nvWsgJGWI2Rut
    CU2nvWsgJGWI2Rut
    HUaIpoLKT3gGOD53

    • Use a T6 Torx driver to remove the eight 5.8 mm‑long screws securing the back cover.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

  3. rEBEVxNkrDU5dsek
    rEBEVxNkrDU5dsek
    rIRRhvkBKVWODhWI
    A4aS52mtPxxkwit5

    • Insert an opening pick at an upward angle between the back cover and the front shell near one of the triggers.

    • If you can't insert your pick here, try along the top or bottom edges of the Steam Deck OLED before sliding it toward the handle.

    • Slide your pick along the edge of the handle to release the clips securing it to the front shell.

  4. yYcl1PRUGUuYu2AV
    yYcl1PRUGUuYu2AV
    Z61KAZVNuuuFxgBL
    5ji5HRJa5qu1niLI

    • Reinsert your pick and slide it along the top and bottom edges until the back cover feels loose.

  5. 3hO2o6jhWtTFtqUB
    3hO2o6jhWtTFtqUB
    HZa1Pau2KaJcrM1I
    2pXBrjoLgvKGSFGx

    • Grip the unclipped handle and pull it away from the front shell to release the remaining clips.

    • Remove the back cover.

  6. OKJYYpHQNvn4X1nk
    OKJYYpHQNvn4X1nk
    GaA5rrvDLfGCHRBc
    d6WmlRapenltwItT

    • Grip the battery cable pull tab, located to the left of the battery.

    • Firmly pull the battery cable straight away from the motherboard shield (toward the battery) to disconnect it.

    • This bundled cable is fairly stiff. If you're having trouble, re-grip the pull tab close to the head of the connector and gently walk it side-to-side as you pull.

    • If the cable pull-tab feels fragile or rips during this process, remove the motherboard shield and disconnect the cable using a spudger.

    • When the battery cable comes free, it might push up on the motherboard shield. Don't worry, as this won't damage anything.

    The pull tab can come off revealing the wires. The instructions should be updated to reflect that catch.

    Khurram Tariq -

  7. 2GFAlFaM62QyIqmL
    2GFAlFaM62QyIqmL
    IMJHriGYVTmlmpNE
    AuiMjoWPJP3rNUSW

    • Use a spudger to flip up the small white locking flap on the right button board interconnect cable ZIF connector.

    • Use tweezers or your fingers to grip the cable's pull tab and slide it straight out of its socket to disconnect it.

    • The pull tab may be labelled C‑R.

  8. JxgFSn411iuTmHXV
    JxgFSn411iuTmHXV
    hsjSQjeqb1DHbNg5
    W11KlQgrfpiETkee

    • The interconnect cable is adhered to the motherboard shield.

    • Insert an opening pick between the interconnect cable and the motherboard shield.

    • Be careful not to crease or tear the cable.

    • If you're having trouble inserting a pick, lightly heat the cable using an iOpener or a hair dryer.

    • Slide your pick along the shield to separate the cable.

    The adhesive is quite strong and it causes the cable to bend. Don't separate the cable from the shield and instead unscrew the shield and lift it towards the right gently to create space to access the SSD.

    Khurram Tariq -

  9. xVsAVwm5nYRCPlYS
    xVsAVwm5nYRCPlYS
    FrqAcp3usMH5YIQG
    I1IogadgJ2WBTh4T

    • During the rest of the repair, it may be helpful to move the interconnect cable over the battery and out of the way of the motherboard shield.

    • Be careful not to crease or strain the cable, as it's still adhered to the battery.

    • Tape the cable in place away from the motherboard shield.

  10. wnPrhtu1rYiX1ZbM
    wnPrhtu1rYiX1ZbM
    wnO5PMcmgZnCq2sG

    • Use your T6 Torx driver to remove the two 3.8 mm‑long screws securing the top left and bottom left corners of the motherboard shield.

  11. AUdJWmS2vDeLnEK3
    AUdJWmS2vDeLnEK3
    21UXwEKEDILPei41
    WZTF3bcws1Hg3Aod

    • If the speaker cable is taped to the bottom edge of the motherboard shield, gently peel it off.

    • Remove the motherboard shield.

  12. oEXZCmlHUOI4YTQa
    oEXZCmlHUOI4YTQa
    kPIGgEUKARRvvAHX
    xHNKtaUswWNMYUsU

    • During reassembly, use the flat end of a spudger to slide the battery connector into its socket on the motherboard.

    This step should come after the SSD is installed.

    Khurram Tariq -

  13. E3MAmiJFGWtDkoMD
    E3MAmiJFGWtDkoMD
    rmdbW14LBeCZ4oak

  14. Mr4KAoVkJJWfOHC3
    Mr4KAoVkJJWfOHC3
    vGrsHOrPfB3mmJsC
    IuePAWGNLEwcdLcM

    • Try not to tear the heat sink sticker, as you'll reuse it during reassembly.

    • Slide the tip of an opening pick under one edge of the heat sink sticker.

    • Peel the sticker up until you can grab it with your fingers.

    • Gently remove the sticker from the heat sink and fan.

    • During reassembly, place the sticker back in its original location. The residual adhesive should stick well.

    • If the residual adhesive isn't sticky anymore, tape the outside edges of the sticker to the heat sink and fan with small strips of tape.

  15. 2DHFGXiikM4EDatt

    • Use your T6 Torx driver to remove the three 3.3 mm‑long screws securing the heat sink.

    • During reassembly, install the screws in the order marked on the heat sink mounts: 1, 2, then 3.

  16. Z4gy5udSqHPcH11U
    Z4gy5udSqHPcH11U
    PyfPTXtJofQhIZPj

    • Lift the heat sink from the motherboard and remove it.

    • Depending on the age of your device, this might require some force. A twisting motion may help loosen the thermal paste.

    • Before reinstalling the heat sink, follow this guide to clean the heat sink and APU and reapply thermal paste.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Steam Deck OLED answers community for help.

Autore

Clay Eickemeyer

Membro da: 19/09/22

64976 Reputazione

0 commenti