Steam Deck OLED Left Thumbstick Disconnection

Scritto Da: Clay Eickemeyer
  • Commenti: 1
Steam Deck OLED Left Thumbstick Disconnection

Difficoltà

Moderate

Passi

7

Tempo Necessario

Nessuna stima

Introduzione

This guide demonstrates how to disconnect the left thumbstick in your Steam Deck OLED.

  1. wg1CPbiBgYbiTVlf
    wg1CPbiBgYbiTVlf
    nJjXUM3KksnJHIgN
    mLdVpQ6WWvINGWuE

    • Turn on your Steam Deck and allow the battery to discharge below 25% before starting your repairs, as a charged lithium-ion polymer battery can be dangerous if accidentally punctured.

    • As an extra precaution, Valve recommends putting your Steam Deck into battery storage mode within the BIOS before starting any internal repairs. Read how to do that here.

    • Power down your Steam Deck and unplug any cables.

    • If you have a microSD card installed, make sure to remove it before opening the Steam Deck. If you attempt to remove the back cover with it still installed, it could snap right in half.

    • During your repair, it can be helpful at times to lay the Steam Deck face-down in its case to protect the thumbsticks and prevent wobble.

  2. CU2nvWsgJGWI2Rut
    CU2nvWsgJGWI2Rut
    HUaIpoLKT3gGOD53

    • Use a T6 Torx driver to remove the eight 5.8 mm‑long screws securing the back cover.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

  3. rEBEVxNkrDU5dsek
    rEBEVxNkrDU5dsek
    rIRRhvkBKVWODhWI
    A4aS52mtPxxkwit5

    • Insert an opening pick at an upward angle between the back cover and the front shell near one of the triggers.

    • If you can't insert your pick here, try along the top or bottom edges of the Steam Deck OLED before sliding it toward the handle.

    • Slide your pick along the edge of the handle to release the clips securing it to the front shell.

  4. yYcl1PRUGUuYu2AV
    yYcl1PRUGUuYu2AV
    Z61KAZVNuuuFxgBL
    5ji5HRJa5qu1niLI

    • Reinsert your pick and slide it along the top and bottom edges until the back cover feels loose.

  5. 3hO2o6jhWtTFtqUB
    3hO2o6jhWtTFtqUB
    HZa1Pau2KaJcrM1I
    2pXBrjoLgvKGSFGx

    • Grip the unclipped handle and pull it away from the front shell to release the remaining clips.

    • Remove the back cover.

  6. OKJYYpHQNvn4X1nk
    OKJYYpHQNvn4X1nk
    GaA5rrvDLfGCHRBc
    d6WmlRapenltwItT

    • Grip the battery cable pull tab, located to the left of the battery.

    • Firmly pull the battery cable straight away from the motherboard shield (toward the battery) to disconnect it.

    • This bundled cable is fairly stiff. If you're having trouble, re-grip the pull tab close to the head of the connector and gently walk it side-to-side as you pull.

    • If the cable pull-tab feels fragile or rips during this process, remove the motherboard shield and disconnect the cable using a spudger.

    • When the battery cable comes free, it might push up on the motherboard shield. Don't worry, as this won't damage anything.

    The pull tab can come off revealing the wires. The instructions should be updated to reflect that catch.

    Khurram Tariq -

  7. eVyqGZ4gRjIItCdp
    eVyqGZ4gRjIItCdp
    6GnJOi2TBm2xBjBf
    B6yPGCjDkG2tF2l2

    • Use the point of a spudger to flip up the small locking flap on the left thumbstick ZIF connector.

    • The pull tab on this connector may be labeled TS.

    • Use tweezers or your fingers to grip the cable's pull tab and slide the connector straight out of its socket to disconnect it.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

Clay Eickemeyer

Membro da: 19/09/22

64976 Reputazione

0 commenti